Details, datasheet, quote on part number: DS9093AB
PartDS9093AB
Category
DescriptionMicrocan Holder
CompanyN.A.
DatasheetDownload DS9093AB datasheet
Quote
Find where to buy
 
  

 

Features, Applications

FEATURES

­ DS9093F snap­in fob for use with F5 MicroCanTM ­ DS9093N angled fob for use with F5 MicroCan ­ DS9093A snap­in angled fob for use with F5 MicroCan

­ DS9093S allows an iButton to be easily and permanently attached to an object using screws or rivets (F5 MicroCan) ­ DS9093P has a locating pin and a single mounting hole for permanent attachment (F5 MicroCan)

­ DS9093RA lock ring firmly fastens F5 package ­ DS9093RB flange enlargement provides additional flange surface area if needed DS9093A

DESCRIPTION

The DS9093 iButton Mount Products offer the user low­ cost fixtures that hold an iButton for thumbpad applications or permanent attachment to an object.

The DS9093F plastic snap­in fob offers the simplest way to mount an iButton for applications that require only momentary contact. The fob can be attached to a key ring for carrying. Do not apply solvents or adhesives to this fob. This might affect the mechanical strength and reliability.

ECopyright 1995 by Dallas Semiconductor Corporation. All Rights Reserved. For important information regarding patents and other intellectual property rights, please refer to Dallas Semiconductor data books.

The DS9093N angled fob is an alternate way to mount an iButton for applications that require only momentary contact. Due to the different mounting technique, the DS9093N can be used with the F5 MicroCan only. The iButton is inserted into this fob by press-fitting. For permanent mount, the iButton can be locked a DS9093RA Lock Ring. The DS9093A is very similar to the DS9093N. It has about the same size as the DS9093N and can be used with the F5 MicroCan only. The iButton is inserted by press­fitting the flange of the MicroCan into the cavity of the fob. In contrast to the DS9093N, no additional parts are needed for permanent mounting. The DS9093A is available in black, blue, green, red and yellow.

is provided along the sides of the plate to reduce incidental damage to the iButton. The DS9093RA Lock Ring is a stainless steel fastener which provides an inexpensive method for firmly attaching an iButton to any item with a pre­punched hole. The iButton is inserted through the hole and is restrained by the flange on the iButton. The DS9093RA Lock Ring is crimped onto the portion of the iButton which protrudes through the hole. The optional DS9093RB Flange Enlargement is a thin stainless steel washer that provides additional surface area to improve retention of the iButton in materials that are very thin or flexible. The DS9093RB is formed with a slight dome to improve the gripping force exerted onto the pre­punched material. The domed side of the washer should face the flange of the iButton, the flat side should face the material. DS9093RA

46.9 3.8 REF. 5.0 DIA. 35.0 SECTION A­A NOTE: PIN IS REPLACED WITH A THRU HOLE DS9093S b) NOTE: PIN IS REPLACED WITH A THRU HOLE 2.0 5.2 DIA. 0.30 mm

The DS9093S and DS9093P allows the user to permanently attach an iButton to an object with one or two screws, rivets, etc. The plastic plate is designed with an inset that accommodates the flange of the F5 package and allows for flush mounting. A protective wall


 

Related products with the same datasheet
DS9093AG
DS9093AR
Some Part number from the same manufacture
DS9093AG Microcan Holder
DS90LV031
DS90LV032
DS9639ACN Ic-dual Line Receiver
DSA10J
DSA12TJ
DSB15TJ
DSP1-BOW Dist.surge Protector
DSP56005
DSP56007FJ66
DSP56303PV66
DSPE56009FJ81
DSR1150-56E472MVA2-EA
DT12-6LS Thermoelectric Module
DT12-8LS
DT420T Sensor Microwave/pir
DT5110VAC Timer Delay on Energise
DT6-6LS Thermoelectric Module
DT640STC Sensor Micro/pIR High Sec
DT700 Sensor Microwave/pir
DT900
Same catergory

HT36F2 : Music Synthesizer 8-Bit MCU The HT36F2 is an 8-bit high performance RISC architecture microcontroller specifically designed for various music applications. It provides an 8-bit MCU and a 4-channel Wavetable synthesizer. It has a built-in 8-bit microprocessor which controls the synthesizer to generate the melody by setting the special register. A HALT.

4792-01 : Power Transformers L-brackets. LOW VOLTAGE RECTIFIER Transformers. Open style with L-bracket mounting. Primary voltage,115 Volts, 60 Hz. Primary and secondary leads 8-10" long. 4-hole horizontal L-bracket mounting. 15 sizes are available, covering the range: to 450 VA. CSA listed (LR 47366). Secondary Voltages (A-A) N.L. Current Volts Amps 229 Colonnade Road, Nepean, Ontario, Canada.

CMO3CEC : 3.3V 5x7mm Surface Mount Crystal Clock Oscillators. CMOS Compatible Tri-State Feature for Auto Test Systems Tape & Reel Packaging ±20ppm Available - Please Contact Factory MODEL Frequency Range (MHz) Frequency Stability (ppm) Overall (Typical) to +85°C Temperature Range (°C) Operating Storage Supply Voltage (V) Input Current (mA) Symmetry CMOS Transistion Times Rise Time (ns) Fall Time (ns) Load "0" Level.

UVV60R5HN : 5x7 mm, 3.3 Volt, Lvpecl/lvds, VCXO. Versatile VCXO to 800 MHz with good jitter (3 ps typical) Used in low jitter clock synthesizers and SONET applications MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. Please see www.mtronpti.com for our complete offering and detailed.

EP8267 : 14 Pin DIP TTL Square-wave Generator. Output frequencies from to 100 MHz ±5% Low Profile 14 pin dual-in-line package Operating temperature range 70 °C Output synchronized using enable line Inherent Delay 4nS Typ. 50% duty cycle Schottky TTL VOH VOL VIK IIH IIL IOS ICCH ICCL TRO NH NL High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Low-Level.

JHV3672 : HIGH Voltage Rectifier Assembly.

ISL85402 : 2.5A Regulator With Integrated High-Side MOSFET For Synchronous Buck Or Boost Buck Converter The ISL85402 is a synchronous buck controller with a 125m? high-side MOSFET and low-side driver integrated. The ISL85402 supports a wide input voltage range from 3V to 36V. Regarding the output current capability from the thermal perspective, the ISL85402 can typically.

3600B/14-100 : Multi-Paired Cable RND DISCRT 14C SHLD TWST 28AWG 100'. s: Manufacturer: 3M ; Product Category: Multi-Paired Cable ; RoHS:  Details ; Wire Size (AWG): 28 ; Stranding: 7 x 36 ; Shielding: Shielded ; Jacket Material: Polyvinyl Chloride (PVC) ; Voltage Rating: 150 V ; Plenum (Y/N): No ; Type: Discrete Wire ; Conductor Material: Tinned Copper ; : Suitable.

CS-FF-MJB : RF Connectors 2.92mm Jack Str. F For IW 1501. Crystek' s RF Connectors are durable, precision connectors designed for high frequency cables. Crystek offers the RF Connectors in SMA, TNC, N-Type, 2.4 mm, and 2.9 mm (K) versions for jacks , plugs , and bulkheads . Constructed using passivated stainless steel, the Crystek RF Connectors provide high performance.

LHF15BB152J : Fixed Inductors, Coils, Choke 1.5mH 750mA Radial -; INDUCTOR 1500UH .75A RADIAL. s: Inductance: 1.5mH ; Tolerance: ±5% ; Package / Case: Radial ; Packaging: Bulk ; Type: - ; Current: 750mA ; Mounting Type: Through Hole ; Q @ Freq: 20 @ 252kHz ; Frequency - Self Resonant: 750kHz ; DC Resistance (DCR): 1.1 Ohm Max ; Shielding: Unshielded ; Applications:.

ERA-6AEB224V : 220K Ohm 0.125W, 1/8W Chip Resistor - Surface Mount; RES 220K OHM 1/8W .1% 0805 SMD. s: Resistance (Ohms): 220K ; Power (Watts): 0.125W, 1/8W ; Tolerance: ±0.1% ; Packaging: Cut Tape (CT) ; Composition: Thin Film ; Temperature Coefficient: ±25ppm/°C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

ERJ-S12F4701U : 4.7K Ohm 0.75W, 3/4W Chip Resistor - Surface Mount; RES ANTI-SULFUR 4.7K OHM 1% 1812. s: Resistance (Ohms): 4.7K ; Power (Watts): 0.75W, 3/4W ; Tolerance: ±1% ; Packaging: Tape & Reel (TR) ; Composition: Thick Film ; Temperature Coefficient: ±100ppm/°C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

1N4739A-T : Diode - Zener - Single Discrete Semiconductor Product 10µA @ 7V 9.1V 1W Through Hole; DIODE ZENER 9.1V 1W DO-41. s: Voltage - Zener (Nom) (Vz): 9.1V ; Power - Max: 1W ; Impedance (Max) (Zzt): 5 Ohm ; Voltage - Forward (Vf) (Max) @ If: 1.2V @ 200mA ; Current - Reverse Leakage @ Vr: 10µA @ 7V ; Tolerance: ±5% ; Mounting Type: Through Hole ; Package / Case:.

V12MLA0805LN : RESISTOR, VOLTAGE DEPENDENT. s: Category / Application: General Use. Surface Mount Multilayer Varistors (MLVs) > MLA Series The MLA Series (also known as "ML" series) family of transient voltage surge suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress a variety of transient events, including those specified in IEC 61000-4-2 or other standards.

 
0-C     D-L     M-R     S-Z