Details, datasheet, quote on part number: AME8500AEEVCA16
PartAME8500AEEVCA16
Category
DescriptionUprocessor Supervisory
CompanyAnalog Micro
DatasheetDownload AME8500AEEVCA16 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The AME8500 family allows the user to customize the CPU reset function without any external components. The user has a large choice of reset voltage thresholds, reset time intervals, and output driver configurations, all of which are preset at the factory. Each wafer is trimmed to the customer's specifications. These circuits monitor the power supply voltage of P based systems. When the power supply voltage drops below the voltage threshold a reset is asserted immediately (within an interval TD1). The reset remains asserted after the supply voltage rises above the voltage threshold for a time interval, TD2. The reset output may be either active high (RESET) or active low (RESETB). The reset output may be configured as either push/pull or open drain. The state of the reset output is guaranteed to be correct for supply voltages greater than 1V. The AME8501 includes all the above functionality plus an overtemperature shutdown function. When the ambient temperature exceeds 80oC a reset is asserted and remains asserted until the temperature falls below 60oC. Space saving SOT23 packages and micropower quiescent current (<3.0A) make this family a natural for portable battery powered equipment.

Note: * External pull-up resistor is required if opendrain output is used. k is recommended.

l Small packages: l 11 voltage threshold options l Tight voltage threshold tolerance l 5 reset interval options l 4 output configuration options l Wide temperature range 85oC l Low temperature coefficient 100ppm/oC(max) l Low quiescent current 3.0A l Thermal shutdown option (AME8501)

Portable electronics Power supplies Computer peripherals Data acquisition systems Applications using CPUs Consumer electronics



GND RESETB/RESET Ground This pin can be ordered as RESET or RESETB. RESET is active high. RESETB is active low. It is also available with an open drain or pushpull output. Positive power supply. A reset is asserted after this voltage drops below a predetermined level. After V DD rises above that level the reset output remains asserted until the end of the reset timeout period.


 

Related products with the same datasheet
AME8500AEETAA16
AME8500AEETAA18
AME8500AEETAA19
AME8500AEETAA20
AME8500AEETAA22
AME8500AEETAA23
AME8500AEETAD15
AME8500AEETAD16
AME8500AEETAD18
AME8500AEETAD19
AME8500AEETAD20
AME8500AEETAD22
Some Part number from the same manufacture Analog Micro
AME8500AEEVCA18 Uprocessor Supervisory

AD8644ARU : Single And Quad +18 V Operational Amplifiers

AIC1714-30CX : Output Voltage: 3.0V; Negative Voltage Regulator

AME8500BEFTBF28 : 3-Pin/5-Pin Micropower P Reset Family

AME8500CEETDF42 : 3-Pin/5-Pin Micropower P Reset Family

OP37GT : Low Noise, Precision, High Speed Operational Amplifier (A(VCL) >- 5)

AIC1722A-38CZTTR : 300ma Low Dropout Linear Regulator

AME8501AEFVDF40 : Uprocessor Supervisory

AD5160BRJZ10-R2 : Data Acquisition - Digital Potentiometer Integrated Circuit (ics) Volatile Tape & Reel (TR) 2.7 V ~ 5.5 V; IC POT DGTL SPI 256POS SOT23-8 Specifications: Number of Circuits: 1 ; Resistance (Ohms): 10K ; Interface: 3-Wire Serial (Chip Select) ; Taps: 256 ; Package / Case: SOT-23-8 ; Packaging: Tape & Reel (TR) ; Voltage - Supply: 2.7 V ~ 5.5 V ; Memory Type: Volatile ; Temperature Coefficient: 45 ppm/C Typical ; Operating Temperat

ADM6319B40ARJZ-R7 : IC,VOLT DETECTOR,FIXED,+2.5V,TSOP,5PIN,PLASTIC

ADUC847BCPZ8-5 : 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, QCC56 Specifications: Data Bus: 8 Bit ; Life Cycle Stage: ACTIVE ; Clock Speed: 0.0328 MHz ; ROM Type: Flash ; Supply Voltage: 2.7 to 3.6 volts ; I/O Ports: 32 ; Package Type: Other, 8 X 8 MM, MO-220-VLLD-2, LFCSP-56 ; Operating Range: Industrial ; Pin Count: 56 ; Operating Temperature: -40 to 85 C (-40 t

 
0-C     D-L     M-R     S-Z