Details, datasheet, quote on part number: AD7994BRU-1
Description4-Channel, 10-Bit ADC With I2C Compatible Interface in 16-Lead Tssop
CompanyAnalog Devices
DatasheetDownload AD7994BRU-1 datasheet
Find where to buy


Features, Applications

4 Channel, 12-/10-Bit ADCs with I2C Compatible Interface in 16-Lead TSSOP AD7994/AD7993 Preliminary Technical Data

FEATURES 12-Bit ADC with Fast Conversion Time: 2 s Four Single-Ended Analog Input Channels Specified for VDD 5.5 V Low Power Consumption Fast Throughput Rate:- 188 KSPS Sequencer Operation Automatic Cycle Mode I2CR Compatible Serial Interface I2CR Interface supports: Standard, Fast, and High-Speed Modes Out of Range Indicator Alert Function Pin-Selectable Addressing via AS Two Versions Allow Five I2C Addresses Shutdown Mode: 1A max 16-Lead TSSOP Package GENERAL DESCRIPTION


The AD7994/AD7993 are 4 channel, 12-/10-bit, high speed, low power, successive-approximation ADCs respectively. The parts operate from a single 5.5 V power supply and feature a conversion time of 2 s. The parts contain a four channel multiplexer and track/hold amplifier which can handle input frequencies in excess of TBD kHz. The AD7994/AD7993 provide a two-wire serial interface which is compatible with I2C interfaces. The parts come in two versions, AD7994-1/ AD7993-1. Each version allows for a minimum of two different I2C addresses. The I2C interface on the AD79940/AD7993-0 supports Standard and Fast I2C Interface Modes. The I2C interface on the AD7994-1/AD7993-1 supports Standard, Fast and two High-Speed I2C Interface Modes. The AD7994/AD7993 normally remain in a shutdown state while not converting, powering up only for conversions. The conversion process can be controlled using the CONVST pin, an Automatic Conversion Cycle selected through software control, or a mode where conversions occur across read Address operations. There are no pipeline delays associated with the part. The reference for the part is applied externally to the REFIN pin and can be in the range 1.2V to VDD. This allows the widest dynamic input range to the ADC.

On-chip registers can be programmed with high and low limits for the conversion result, and an open drain Out of Range Indicator output (ALERT), becomes active when the programmed high or low limits are violated by the conversion result. This output can be used as an interrupt.

2 s Conversion time with low power consumption. 2. I2C Compatible Serial Interface with pin selectable addresses. Two AD7994/AD7993 versions allow five AD7994/AD7993 devices to be connected to the same serial bus. 3. The parts feature automatic shutdown while not converting to maximize power efficiency. Current consumption is 1A max when in shutdown. 4. Reference can be driven up to the power supply. 5. Out of Range Indicator which can be software disabled/ enabled. 6. Oneshot and automatic conversion rates. 7. No Pipeline Delay The part features a standard successive-approximation ADC.

SMBus is a trademark and is a registered trademark of Philips Corporation

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 Fax: 781/326-8703 Analog Devices, Inc., 2002

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Parameter DYNAMIC PERFORMANCE Signal to Noise + Distortion (SINAD)2 Signal to Noise Ratio (SNR)2 Total Harmonic Distortion (THD)2 Peak Harmonic or Spurious Noise (SFDR)2 Intermodulation Distortion (IMD)2 Second Order Terms Third Order Terms Aperture Delay Aperture Jitter Channel-to-Channel Isolation Full Power Bandwidth DC ACCURACY Resolution Integral Nonlinearity2 Differential Nonlinearity2 Offset Error2 Offset Error Match2 Gain Error2 Gain Error Match2 ANALOG INPUT Input Voltage Ranges DC Leakage Current Input Capacitance REFERENCE INPUT REFIN Input Voltage Range DC Leakage Current Input Capacitance Input Impedance LOGIC INPUTS (SDA, SCL, CONVST ) Input High Voltage, VINH Input Low Voltage, VINL Input Leakage Current, IIN Input Capacitance, CIN2,3 Input Hysteresis, VHYST LOGIC OUTPUTS (SDA) Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance2,3 Output Coding LOGIC OUTPUTS (ALERT) Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance2,3 CONVERSION RATE Conversion Time Track/Hold Acquisition Time Throughput Rate B Version1 TBD to REFIN 1.2 to VDD 1 TBD 1 10 TBD dB

(VDD +5.5 V, unless otherwise noted ; REFIN 2.5 V; fSCL = 3.4 MHz unless A MIN to TMAX, unless otherwise noted.)

See Interface Section Full-Scale step input Sine wave input 30 Standard mode SCL = Fast Mode SCL = 400 High-Speed Mode SCL

+5.5 V, unless otherwise noted ; REF f AD7994SPECIFICATIONS1 (otherwise noted; T , unless otherwise noted.)

Parameter POWER REQUIREMENTS VDD IDD Peak Current Power Down Mode , Interface Inactive Interface Active

2.7/5.5 V min/max TBD A max Digital Inputs V or VDD Peak Current during conversion VDD 3.6 V. VDD 5.5 V. VDD 3.6 V. VDD 5.2 V. VDD 5.5 V.

NOTES 1 Temperature ranges as follows: B Version: +85C. 2 See Terminology. 3 Sample tested +25C to ensure compliance. 4 See POWER VERSUS THROUGHPUT RATE section. Specifications subject to change without notice.


Related products with the same datasheet
Some Part number from the same manufacture Analog Devices
AD7997 8-Channel, 10-Bit ADC With I2C Compatible Interface in 20-Lead Tssop
AD800 45 or 52 MBPS Clock And Data Recovery ic
AD8001 800 Mhz, 50 MW Current Feedback Amplifier
AD8002AN Dual 600 Mhz, 50 MW Current Feedback Amplifier
AD8004 Quad 3000 V/µs 35mW Current Feedback Amplifier
AD8004AN Quad 3000 V/ms, 35 MW Current Feedback Amplifier
AD8004AR Quad 3000 V/µs 35mW Current Feedback Amplifier
AD8004AR-14-REEL7 Quad 3000 V/us, 35 MW Current Feedback Amplifier
AD8005 Ultralow Power, 170 MHZ And Slew Rate of 280 V/s
AD8005AN 270 Mhz, 400 Microa Current Feedback Amplifier
AD8005AR-REEL Ultralow Power, 170 MHZ And Slew Rate of 280 V/s
AD8005ART 270 Mhz, 400 Microa Current Feedback Amplifier
AD8005ART-REEL Ultralow Power, 170 MHZ And Slew Rate of 280 V/s
AD8007 Single Low Distortion High Speed Amp
AD8009 1 Ghz, 5,500 V/µs Low Distortion Amplifier

AME385BEAS : Micropower Voltage Reference Diode


ADM2485BRWZ : High Speed Isolated RS-485 Transceiver with Integrated Transformer Driver The ADM2485 differential bus transceiver is an integrated, galvanically isolated component designed for bidirectional data communication on multipoint bus transmission lines. It is designed for balanced transmission lines

AD5044 : Fully Accurate 12-/14-/16-Bit VOUT NanoDAC SPI Interface 2.7 V To 5.5 V In A TSSOP Preliminary The AD5024/44/64 are low power, quad 12-/14-/16-bit buffered voltage-out DACs offering relative accuracy specs of 1 LSB INL with individual and common reference pin options and can operate from a si

AME8833BEEV300Z : High Psrr, 150ma CMOS LDO

AD622ANZ : IC, INSTRUMENT AMP, 1MHZ, 118DB, DIP-8 Specifications: No. of Amplifiers: 1 ; Input Offset Voltage: 125V ; Gain dB Min: 1dB ; Gain dB Max: - ; Bandwidth: 1MHz ; Amplifier Output: Single Ended ; Noise Figure Typ: - ; CMRR: 118dB ; Slew Rate: 1.2V/s ; Supply Voltage Range: 2.6V to 18V ; Supply Current: 900A ; Amplifier Case Style: D

AD5060BRJ-1REEL7 : SERIAL INPUT LOADING, 10 us SETTLING TIME, 16-BIT DAC, PDSO8 Specifications: Package Type: SOT-23, 8 PIN ; Screening Level: AUTOMOTIVE ; Pins: 8 ; Operating Temperature: -40 to 125 C (-40 to 257 F)

ADP1763-1.3-EVALZ : Power Management IC Development Tools 1.3V VOUT Eval Board Analog Devices ADP176 CMOS Linear Regulators product line includes low noise, low dropout (LDO) linear regulators. The ADP176 regulators operate from a single input supply voltage as low as 1.10V and offer up to 3A of output current. The design of these regulators eliminates the requirement for a

0-C     D-L     M-R     S-Z