|Datasheet||Download ADDC02805 datasheet
FEATURES V dc Input, 100 W Output V dc Input, 66 W Output (ADDC02803SC) Integral EMI Filter Designed to Meet MIL-STD-461D Low Weight: 80 Grams NAVMAT Derated Many Protection and System Features
SENSE + SENSE ADJUST STATUS RETURN VAUX INHIBIT SYNC ISHARE TEMP VIN +VIN EMI FILTER INPUT SIDE CONTROL CIRCUIT FIXED FREQUENCY DUAL INTERLEAVED POWER TRAIN RETURN OUTPUT FILTER RETURN +VOUT OUTPUT SIDE CONTROL CIRCUIT
APPLICATIONS Commercial and Military Airborne Electronics Missile Electronics Space-Based Antennae and Vehicles Mobile/Portable Ground Equipment Distributed Power Architecture for Active Array Radar
The ADDC02803SC and ADDC02805SA hybrid dc/dc converters with integral EMI filters offer the highest power density of any dc/dc converter with their features and in their power range available today. The converters with integral EMI filters are fixed frequency, 1 MHz square wave switching dc/dc power supplies. They are not variable frequency resonant converters. In addition to many protection features, these converters have system level features that allow them to be used as components in larger systems as well as stand-alone power supplies. The units are designed for high reliability and high performance applications where saving space and/or weight are critical. The ADDC02803SC and ADDC02805SA are available in three screening grades; all grades use a hermetically sealed, molybdenum based hybrid package. Three screening levels are available, including military SMD.
to 60 W/cubic inch power density with an integral EMI filter designed to meet all applicable requirements in MILSTD-461D when installed in a typical system setup. 2. Light weight: 80 grams 3. Operational and survivable over a wide range of input conditions: V50 V dc; survives low line, high line and positive and negative transients. See section entitled: Input Voltage Range. 4. High reliability; NAVMAT derated 5. Protection features include: Output Overvoltage Protection Output Short Circuit Current Protection Thermal Monitor/Shutdown Input Overvoltage Shutdown Input Transient Protection 6. System level features include: Current Sharing for Parallel Operation Inhibit ControlOutput Status Signal Synchronization for Multiple Units Input Referenced Auxiliary Voltage Supply
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1998
Parameter INPUT CHARACTERISTICS Steady State Operating Input Voltage Range 1 Abnormal Operating Input Voltage Range (Per MIL-STD-704D)1 Input Overvoltage Shutdown No Load Input Current Disabled Input Current OUTPUT CHARACTERISTICS 2, 3 Output Voltage (VO) Case Temp Full +25°C Full +25°C Full +25°C Full +25°C
(TC = +25C, VIN 0.5 V dc, unless otherwise noted; full temperature range to +90C; all temperatures are case and TC is the temperature measured at the center of the package bottom.)
Line Regulation Load Regulation Output Ripple/Noise4 Output Current (IO) Output Overvoltage Protection Output Current Limit Output Short Circuit Current ISOLATION CHARACTERISTICS Isolation Resistance
DYNAMIC CHARACTERISTICS Output Voltage Deviation Due to Step Change in Load +25°C V Response Time Due to Step Change in Load +25°C V Soft Start Turn-On Time 5 THERMAL CHARACTERISTICS Efficiency I +25°C Max Min +25°C Max Min VI V
10 A di/dt 10 A, di/dt 0.5 A/ µs, Time for VOUT to Return within 2% of Final Value 20 A, From Inhibit High to Status High 2 A IOH 400 µA IOL 1 mA IAUX = 5 mA, Load Current 20 A
Hottest Junction Temperature 6 CONTROL CHARACTERISTICS Clock Frequency ADJUST (Pin 3) V ADJ STATUS (Pin 4) VOH VOL VAUX (Pin 5) VO (nom) INHIBIT (Pin 6) VIL IIL VI (Open Circuit) SYNC (Pin 7)7 VIH IIH ISHARE (Pin 8) TEMP (Pin 9)
V dc upper limit rated for transient condition to 50 ms. V dc lower limit rated for continuous operation during emergency condition. Steady state and abnormal input voltage range require source impedance sufficient to insure input stability at low line. See sections entitled System Instability Considerations and Input Voltage Range. 2 Measured at the remote sense points. 3 Unit regulates output voltage to zero load. 4 CLOAD 0. 5 Output is fully loaded into a constant resistive load. 6 Refer to section entitled Thermal Characteristics for more information. 7 Unit has internal pull-down; refer to section entitled Pin 7 (SYNC). Specifications subject to change without notice.
INHIBIT. 50 V dc, V dc SYNC. 8.0 V dc, V dc ISHARE. 6 V dc, V dc TEMP. 12 V dc, V dc Common-Mode Voltage, Input to Output. V dc Lead Soldering Temp (10 sec). +300°C Storage Temperature. to +150°C Maximum Junction Temperature. +150°C Maximum Case Operating Temperature. +125°C
*Absolute maximum ratings are limiting values, to be applied individually, and beyond which the serviceability of the circuit may be impaired. Functional operability under any of these conditions is not necessarily implied. Exposure of absolute maximum rating conditions for extended periods of time may affect device reliability.Description
to +85°C Hermetic Package to +90°C Hermetic Package to +125°C Hermetic Package to +85°C Hermetic Package to +90°C Hermetic Package to +125°C Hermetic Package
100% production tested. 100% production tested at +25°C, and sample tested at specified temperatures. Sample tested only. Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. All devices are 100% production tested +25°C. 100% production tested at temperature extremes for military temperature devices; guaranteed by design and characterization testing for industrial devices.
Feedback loop connection for remote sensing output voltage. Must always be connected to output return for proper operation. +SENSE Feedback loop connection for remote sensing output voltage. Must always be connected to +VOUT for proper operation. ADJUST Adjusts output voltage setpoint. STATUS Indicates output voltage is within 5% of nominal. Active high referenced to SENSE (Pin 1). VAUX Low level dc auxiliary voltage supply referenced to input return (Pin 10). INHIBIT Power Supply Inhibit. Active low and referenced to input return (Pin 10). SYNC Clock synchronization input for multiple units; referenced to input return (Pin 10). ISHARE Current share pin which allows paralleled units to share current typically within 5% at full load; referenced to input return (Pin 10). TEMP Case temperature indicator and temperature shutdown override; referenced to input return (Pin 10). VIN Input Return. +VIN +28 V Nominal Input Bus. +VOUT V dc Output V dc Output (ADDC02803SC). +VOUT V dc Output V dc Output (ADDC02803SC). +VOUT V dc Output V dc Output (ADDC02803SC). RETURN Output Return. RETURN Output Return. RETURN Output Return.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
|Some Part number from the same manufacture Analog Devices|
|ADDC02805SA 28V/100W DC/DC Converter Vin=16-50V, Vo=5V@20A W/emi Filter|
|ADDC02805SA28 28V/66W DC/DC Converter Vin=16-50V, Vo=3.3V@21A W/emi Filter|
|ADDC02805SAKV 28 V/66 W/100 W DC/DC Converters With Integral Emi Filter|
|ADDC02808PB 28 V, 200 W Pulsed DC/DC Converter With Integral Emi Filter|
|ADDC02808PBTV/QMLH 28 v, 200 W Pulsed DC/DC Converter With Integral Emi Filter|
|ADDC02812DA 28V/100W DC/DC Converter Vin=16-50V, Vo= 12V@8.3A W/emi Filter|
|ADDC02812DATV/QMLH 28 V/100 W DC/DC Converters With Integral Emi Filter|
|ADDC02815DA 28V/100W DC/DC Converter Vin=16-50V, Vo= 12V@8.3A W/emi Filter|
|ADDC02815DATV/QMLH 28 V/100 W DC/DC Converters With Integral Emi Filter|
|ADDC02828SA 28 V/100 W DC/DC Converter With Integral Emi Filter|
|ADDC02828SA28 V/100 W DC/DC Converter With Integral Emi Filter|
|ADDC02828SAKV 28 V/100 W DC/DC Converter With Integral Emi Filter|
|ADDS-2101-3V ADSP-2100 Family Development Tools|
AD7875 : CMOS, Complete 12-Bit 100 Khz, Sampling ADC With Uni 5V Input Range
AME8500AEETBA13 : 3-Pin/5-Pin Micropower P Reset Family
AME8501BEFTCE46 : 3-Pin/5-Pin Micropower P Reset Family
ADP1706 : Low Dropout, CMOS Linear Regulator Product Description The ADP1706/ADP1707/ADP1708 are CMOS, low dropout linear regulators that operate from 2.5 V to 5.5 V and provide up to 1 A of output current. Using an advanced proprietary architecture, they provide high power supply rejection and
ADM6316DY47ARJZ-R7 : IC,POWER SUPPLY SUPERVISOR,TSOP,5PIN,PLASTIC
ADM6316LARJ38DY-R7 : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)
ADM6316LARJ42AX-R7 : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)
ADM6318BX34ARJ-R7 : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)
ADM6320DW29ARJ-RL7 : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, ROHS COMPLIANT, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)
GP1A15 : High Sensing Accuracy Type Opic Photointerrupter. 1. High sensing accuracy ( slit width ) 2. Built-in schmidt trigger circuit 3. Low threshold input current ( IFLH : MAX. ) 4. Low level supply current ( ICCL : MAX. ) 5. Operating supply voltage 17V 6. TTL and CMOS compatible output High Sensing Accuracy Type OPIC Photointerrupter Internal connection diagram Voltage regulator 1 Amp. VO 5 GND Slit width.
SFH320 : SMT Phototransistors. Phototransistor in SMT TOPLED® Package. Wesentliche Merkmale Speziell geeignet für Anwendungen im Bereich von 380 nm bis 1150 nm (SFH 320) und bei 880 nm (SFH 320 FA) Hohe Linearität P-LCC-2 Gehäuse Gruppiert lieferbar Für alle Lötverfahren geeignet Anwendungen Miniaturlichtschranken für Gleich- und Wechsellichtbetrieb Lochstreifenleser Industrieelektronik ,,Messen/Steuern/Regeln" Typ Type.
DCM6048S12 : Dc-dc Converter. Open Frame Telecom DC-DC Converter -48 VDC Input ETSI Compliant NEBS Compliant Convection-cooled High Power Density in 2 Small Package Sizes Covered Versions Available Input Voltage Range Input Current Input Reverse Voltage Protection Input Transient Undervoltage Lockout Protection 48 VDC nominal - 75 VDC). Can be configured as -48 VDC input 1.5 A typical,.
M6027AHFSN : 3.2 x 5 mm, 3.0 Volt, Clipped Sinewave, Tcxo/tcvcxo. Ultra-miniature size Ideal for handheld and portable devices MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. Please see www.mtronpti.com for our complete offering and detailed datasheets. Contact us for your application specific.
7LB176 : Differential BUS Transceivers. ANSI Standard TIA/EIA-485-A and ISO 8482:1987(E) High-Speed Low-Power LinBiCMOS Circuitry Designed for High-Speed Operation in Both Serial and Parallel Applications Low Skew Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments Very Low Disabled Supply Current. 200 µA Maximum Wide Positive and Negative Input/Output Bus Voltage.
HSC2X2LG3MNM : Panduct Type HS Hinged Cover Solid Wall Wiring Duct/Raceway. s: Accessory Type: Hinged Cover Wiring Duct ; For Use With: Control Panel Wiring & Communication Closets ; External Height: 50.3mm ; Raceway / Duct Material: Lead Free PVC ; External Width: 55.1mm ; Raceway / Duct Color: Grey ; Series: Solid Wall.
73610 : Clothing Static Control, Esd, Clean Room Product; COAT LAB W/CUFFS BLUE XSMALL. s: Clothing Type: Lab Coat with Cuffs ; Color: Blue ; Size: XSmall ; : 4mm Snap Stud on Hip, Conductive Fabric on Cuff ; Material: Polyester ; Lead Free Status: Lead Free ; RoHS Status: Vendor Undefined.
EMA50DTBD : Gold Through Hole, Right Angle Card Edge, Edgeboard Connector Connectors, Interconnect Non Specified - Dual Edge; CONN EDGECARD 100PS R/A .125 SLD. s: Card Thickness: 0.062" (1.57mm) ; Card Type: Non Specified - Dual Edge ; Contact Finish: Gold ; Mounting Type: Through Hole, Right Angle ; : - ; Number of Positions: 100 ; Number of Rows: 2 ; Pitch: 0.125".
D38999/26JD19SA : Composite, Olive Drab Cadmium Plated Free Hanging (In-Line) Circular Connectors, Interconnect Plug, Female Sockets; CONN PLUG 19POS STRAIGHT W/SCKT. s: Connector Type: Plug, Female Sockets ; Shell Size - Insert: 15-19 ; Mounting Type: Free Hanging (In-Line) ; Fastening Type: Threaded ; : Shielded ; Packaging: Bulk ; Number of Positions: 19 ; Termination:.
T1008-8R2G : Fixed Inductors, Coils, Choke 8.2µH 170mA 1008 (2520 Metric) Ceramic; INDUCTOR WW 8.2UH 170MA 1008 2%. s: Inductance: 8.2µH ; Tolerance: ±2% ; Package / Case: 1008 (2520 Metric) ; Packaging: Tape & Reel (TR) ; Type: Ceramic ; Current: 170mA ; Mounting Type: Surface Mount ; Q @ Freq: 20 @ 7.9MHz ; Frequency - Self Resonant: 25MHz ; DC Resistance.
DBMAME25PA101 : Gold Panel Mount D-sub Connectors, Interconnect Plug, Male Pins; DSUB 25 M CRIMP 50U CAD. s: Connector Type: Plug, Male Pins ; Contact Finish: Gold ; : - ; Flange Feature: Board Side (4-40) ; Mounting Type: Panel Mount ; Number of Positions: 25 ; Number of Rows: 2 ; Termination: Crimp ; Contact Finish Thickness: 50µin (1.27µm) ; Connector Style: D-Sub.
FMA3011-000 : 12700 MHz - 16000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER. s: Amplifier Type: Power Amplifier ; Applications: RF Microwave ; RoHS Compliant: RoHS ; Frequency Range: 12700 to 16000 MHz ; Minimum Gain: 25.2 dB ; Package Type: ROHS COMPLIANT PACKAGE-16 ; Nominal Impedance: 50 ; Operating Temperature: -40 to 85 C (-40 to 185 F).
GSC103-10M0720 : RF/MICROWAVE DIRECTIONAL COUPLER. s: RF Coupler Type: Uni-Directional.
0507004.MXEP : Cartridge Fuses 650VDC 4A Axial Leaded. Littelfuse 507 Series Fuses provide enhanced over-current protection for high voltage applications. The 6x32mm ceramic body fuses have current ratings of 1A to 8A and a rated voltage of 650VDC with an interrupting rating of 150A@650VDC. The 507 Series enables compact design for power conversion equipment demanding.