Details, datasheet, quote on part number: OP196GS
DescriptionMicropower, Rail-to-rail Input And Output Operational Amplifiers
CompanyAnalog Devices
DatasheetDownload OP196GS datasheet
Cross ref.Similar parts: MAX4241ESA, LT1494CS, MAX4091ASA, MAX4240ESA, MAX495CSA, MAX495ESA, OPA241, TLV2211, TLV2221
Find where to buy


Features, Applications

FEATURES Rail-to-Rail Input and Output Swing Low Power: 60 A/Amplifier Gain Bandwidth Product: 450 kHz Single-Supply Operation: 12 V Low Offset Voltage: 300 V max High Open-Loop Gain: 500 V/mV Unity-Gain Stable No Phase Reversal APPLICATIONS Battery Monitoring Sensor Conditioners Portable Power Supply Control Portable Instrumentation

Micropower, Rail-to-Rail Input and Output Operational Amplifiers OP196/OP296/OP496

The OP196 family of CBCMOS operational amplifiers features micropower operation and rail-to-rail input and output ranges. The extremely low power requirements and guaranteed operation from 12 V make these amplifiers perfectly suited to monitor battery usage and to control battery charging. Their dynamic performance, including 26 nV/Hz voltage noise density, recommends them for battery-powered audio applications. Capacitive loads 200 pF are handled without oscillation. The OP196/OP296/OP496 are specified over the HOT extended industrial to +125C) temperature range. 3 V operation is specified over the to 125C temperature range. The single OP196 and the dual OP296 are available 8-lead SO-8 surface mount packages. The dual OP296 is available in 8-lead PDIP. The quad OP496 is available in 14-lead plastic DIP and narrow SO-14 surface-mount packages.

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 Fax: 781/326-8703 Analog Devices, Inc., 2002

Input Bias Current Input Offset Current
Common-Mode Rejection Ratio Large Signal Voltage Gain
Long-Term Offset Voltage Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage Swing High
0 V VCM 0.30 V VOUT +125C G Grade, Note 1 H Grade, Note 1 G Grade, Note 2 H Grade, Note 2 mA

Output Current POWER SUPPLY Power Supply Rejection Ratio Supply Current per Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density

NOTES 1 Long-term offset voltage is guaranteed a 1,000 hour life test performed on three independent lots 12 5C, with an LTPD 1.3. 2 Offset voltage drift is the average of the to +25C delta and the to +125C delta. Specifications subject to change without notice.

Common-Mode Rejection Ratio Large Signal Voltage Gain Long-Term Offset Voltage Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage Swing High Output Voltage Swing Low POWER SUPPLY Supply Current per Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density

0 V VCM k G Grade, Note 1 H Grade, Note 1 G Grade, Note 2 H Grade, Note 100 A VOUT 100 k
dB V/mV V mV V/C mV A V/s kHz Degrees V p-p nV/Hz pA/Hz

NOTES 1 Long-term offset voltage is guaranteed a 1,000 hour life test performed on three independent lots 12 5C, with an LTPD 1.3. 2 Offset voltage drift is the average of the to 25C delta and the to 125C delta. Specifications subject to change without notice.


Related products with the same datasheet
Some Part number from the same manufacture Analog Devices
OP200 Dual Low Offset, Low Power Operational Amplifier
OP200GP Dual Low Offset, Low Power Operational Amp
OP200GS Dual Low Offset, Low Power Operational Amplifier
OP207 Dual, Low Vos
OP213 Low Noise, Low Drift Single-supply Operational Amplifiers
OP215 Dual, JFET Input
OP2177 Precision, Single, Low Noise Low Input Bias Current Operational Amplifiers
OP220 Dual Micropower Operational Amplifier
OP221 Dual Low Power Operational Amplifier, Single or Dual Supply

AD7572ASQ03 : Lc2mos Complete, High Speed 12-bit ADC

AD840SE-883B : Single Wideband, Fast Settling op Amp

ADP1823ACPZ-R7 : Synchronous Buck PWM, Step-down, Dc-to-dc Controller

ADP7102ARDZ-R7 : 20 V, 300 MA, Low Noise, CMOS LDO The ADP7102 is a CMOS, low dropout linear regulator that operates from 3.3 V to 20 V and provides up to 300 mA of output current. This high input voltage LDO is ideal for regulation of high performance analog and mixed signal circuits operating from 19 V to 1.22 V


AD5317BRUZ-REEL7 : Data Acquisition - Digital To Analog Converter (dac) Integrated Circuit (ics) Tube Single Supply; IC DAC 10BIT QUAD W/BUFF 16TSSOP Specifications: Data Interface: DSP, MICROWIRE, QSPI, Serial, SPI ; Number of Bits: 10 ; Operating Temperature: -40C ~ 105C ; Package / Case: 16-TSSOP (0.173", 4.40mm Width) ; Packaging: Tube ; Voltage Supply Source: Single Supply ; Settling Time: 7s ; Lead Free Status: Lead Free ; RoHS Status

ADG442BRZ : Interface - Analog Switches, Multiplexers, Demultiplexer Integrated Circuit (ics); IC SWITCH QUAD SPST 16SOIC Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ADM6320BY42ARJ-RL : 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 Specifications: Package Type: SOT23, Other, MO-178AA, SOT-23, 5 PIN ; Operating Temperature: -40 to 85 C (-40 to 185 F)


ADUCM3029 : Ultra Low Power ARM Cortex-M3 MCU with Integrated Power Management and 256 KB of Embedded Flash Memory The ADuCM3027/ADuCM3029 microcontroller units (MCUs) are ultra low power microcontroller systems with integrated power management for processing, control, and connectivity. The MCU system is based on the ARM Cortex-M3 processor, a collection of digital peripherals, embedded SRAM and flash memory, an

ADM2795EBRWZ-RL7 : RS-422/RS-485 Interface IC Iso EMC Protected RS-485 Transceiver Analog Devices ADM2795E Transceivers are 5kVrms signal-isolated RS-485 transceivers. The transceivers provide up to 42V of AC/DC peak bus overvoltage fault protection on the RS-485 bus pins. Developed using iCoupler technology, the transceivers combine a 3-channel isolator, RS-485 transceiver,

Same catergory

CY54FCT273ATDMB : 8-bit Register. Data sheet acquired from Cypress Semiconductor Corporation. Data sheet modified to remove devices not offered. The FCT273T consists of eight edge-triggered D-type flip-flops with individual D inputs and Q outputs. The common buffered clock (CP) and master reset (MR) load and reset all flip-flops simultaneously. The is an edge-triggered register. The state.

J111 : Switch. Low On-Resistance: 30 W Fast Switching--tON: 4 ns Low Leakage: 5 pA Low Capacitance: 3 pF Low Insertion Loss Low Error Voltage High-Speed Analog Circuit Performance Negligible "Off-Error," Excellent Accuracy Good Frequency Response, Low Glitches Eliminates Additional Buffering APPLICATIONS Analog Switches Choppers Sample-and-Hold Normally "On" Switches.

INA212 : Voltage Output, High/Low-Side Measurement, Bi-Directional Zero-Drift Series Current Shunt Monitor The INA210, INA211, INA212, INA213, and INA214 are voltage output current shunt monitors that can sense drops across shunts at common-mode voltages from -0.3V to 26V, independent of the supply voltage. Five fixed gains are available: 50V/V, 100V/V, 200V/V,.

TM20P-66P : Modular Connectors(plug for Copper Foil, Stranded wire flat type Cable).

1327505 : RF Adapters - Between Series N JACK UHF JACK. The Between Series RF Adapters from Bomar Interconnect are available in several types, including BNC, N, GSK, RCA, TNC, Mini-UHF, UHF, and 7/16, with male/male, female/female, and male/female configurations. Bomar's Between Series RF Adapters are nickel plated with machined brass, have impedance of 50 Ohms,.

BZB784-C6V8,115 : Zener Diode Array. s: Zener Voltage Vz Typ: 6.8V ; Diode Configuration: Dual Common Anode ; Power Dissipation Pd: 350mW ; Operating Temperature Range: - ; Diode Case Style: SOT-323 ; No. of Pins: 3.

GS3-100-2402-J : Metal Film Resistors - Through Hole 3WATT 24KOHM 5%. s: Manufacturer: IRC ; Product Category: Metal Film Resistors - Through Hole ; RoHS: In Transition ; Resistance: 24 KOhms ; Tolerance: 5 % ; Power Rating: 3 Watts ; Voltage Rating: 1 KVolt ; Temperature Coefficient: 100 PPM / C ; Termination Style: Axial ; Operating Temperature Range: - 55 C to + 175 C ; Dimensions:.

TEH70M5R00JE : Thick Film Resistors - Through Hole 70watt 5ohm 5%. The Ohmite TEH Series 70 Watt TO247 Package Thick Film Power Resistors are rated at 25°C case temperature and 1000 hrs @ rated power with non-inductive performance and low thermal resistance. The RoHS compliant design two or three terminals. The Ohmite 70 Series 70 Watt TO247 Package Thick Film Power.

FN3120H-110-35 : 300V, 520V 110A Line Filter Filter Power Line; FILTER 3-PHASE EMC/RFI 110A. s: Inductance: - ; Current: 110A ; Filter Type: Power Line ; Termination Style: Terminal Block ; Mounting Type: Chassis Mount ; Voltage - Rated: 300V, 520V ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

767140-6 : Gold Surface Mount Board To Board - Arrays, Edge Type, Mezzanine Connectors, Interconnect Plug, Outer Shroud Contacts; CONN PLUG 228POS .025 VERT SMD. s: Connector Type: Plug, Outer Shroud Contacts ; Number of Positions: 228 ; Number of Rows: 2 ; Contact Finish: Gold ; Mounting Type: Surface Mount ; Pitch: 0.025" (0.64mm) ; : Board Guide, Ground Bus (Plane).

1858170 : Free Hanging (In-Line) Terminal Block - Headers, Plug And Socket Connectors, Interconnect Plug, Male Pins; PLUG TERM BLOCK 16POS 3.81MM. s: Terminal Block Type: Plug, Male Pins ; Positions Per Level: 16 ; Pitch: 0.150" (3.81mm) ; Number of Levels: 1 ; Header Orientation: - ; Plug Wire Entry: 180 ; Termination: Screw ; Wire Gauge: 14-30 AWG ; Current:.

TNPW2010105KBETF : 105K Ohm 0.4W Chip Resistor - Surface Mount; RES 105K OHM .40W 0.1% 2010. s: Resistance (Ohms): 105K ; Power (Watts): 0.4W ; Tolerance: 0.1% ; Packaging: Tape & Reel (TR) ; Composition: Thin Film ; Temperature Coefficient: 25ppm/C ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant.

SBG3030CT-T : Diodes, Rectifier - Array Discrete Semiconductor Product 30A 30V Schottky; DIODE SCHOTTKY CC 30V 30A D2-PAK. s: Diode Type: Schottky ; Diode Configuration: 1 Pair Common Cathode ; Voltage - DC Reverse (Vr) (Max): 30V ; Current - Average Rectified (Io) (per Diode): 30A ; Voltage - Forward (Vf) (Max) @ If: 550mV @ 15A ; Current - Reverse Leakage @ Vr: 1mA @ 30V ; Reverse.

A22-SG-10A : SPST-NO Pushbutton Switch Off-On 10A (AC/DC); SWITCH PUSH SPST-NO 10A 110V. s: Type: Standard ; Circuit: SPST-NO ; Switch Function: Off-On ; Current Rating: 10A (AC/DC) ; Voltage Rating - AC: 110V ; Voltage Rating - DC: 24V ; Actuator Type: Round, Button, Mushroom ; Color - Actuator/Cap: Green ; Illumination Type, Color: - ; Illumination Voltage (Nominal):.

MMB106K35AG : CAPACITOR, METALLIZED FILM, POLYESTER, 35 V, 10 uF, THROUGH HOLE MOUNT. s: Configuration / Form Factor: Leaded Capacitor ; Technology: Film Capacitors ; Applications: General Purpose ; Electrostatic Capacitors: Polyester ; RoHS Compliant: Yes ; Capacitance Range: 10 microF ; Capacitance Tolerance: 10 (+/- %) ; WVDC: 35 volts ; Mounting Style: Through.

STPS320S : 3 A, 20 V, SILICON, RECTIFIER DIODE. s: Package: PLASTIC PACKAGE-2 ; Pin Count: 2 ; IF: 3000 mA ; VRRM: 20 volts ; RoHS Compliant: RoHS.

GL-BL30 : GlacialLight Arcturus 30W Low Bay Light Achieves 107 Lumens per Watt - GL-BL30. GlacialLight, the lighting division of GlacialTech Inc., introduces the newest model in its Arcturus Bay Light series. The GL-BL30 is a durable LED low bay light that uses 30W of electricity to produce up to 3200 lumens. With a highly efficient CoB LED, the GL-BL30 sips.

0-C     D-L     M-R     S-Z