Details, datasheet, quote on part number: BWR-12/210Series
CategoryPower Management => DC-DC Converters => Single Output
Description5w, DC/DC Converter
CompanyDatel, Inc.
DatasheetDownload BWR-12/210Series datasheet


Features, Applications


Small size, x 0.45" Full 5 Watts output power No external components required Drop-in replacements for many standard, x 1" DC/DC's Wide input voltage ranges: or 36-72V Standard output voltages: ±12, ±15 Volts Guaranteed efficiencies to 80% Fully regulated and isolated (1000Vdc guaranteed) Output overvoltage protection and current limiting to +95oC operating temperature Shielded cases (5 sides) UL1950, CSA 22.2 No. 234, and IEC950 Modifications and customs for OEM's

The migration to distributed power is accelerating. The critical need for accurate voltages, tight regulation and rapid transient response is propelling the move to power processing at the "point-of-use" with low-power DC/DC converters physically located right at their loads. DATEL's miniature, full featured, 5 Watt BWR Models were specifically designed for today's demanding distributed power architectures in aerospace, marine, telecom and computer applications. The converters' small size x 0.45"), full 5 Watt output capability and low cost give system architects unprecedented design and layout flexibility. Occupying less than 0.5in3 total volume, these extremely compact, fully regulated and isolated (1000Vdc) modules are available with or ±15 Volt outputs. Input voltage ranges are either 18-36 Volts ("D24" models) or 36-72 Volts ("D48" models). Although their overall size is 50-75% smaller than many similarly rated power modules, these x 1" BWR Models are exact, drop-in, pin-for-pin replacements for many standard x 1" and 2", 5 Watt modules. They achieve their small size and low cost by exploiting a novel feedback approach that does not depend upon traditional optocoupler techniques. All models are 5-side shielded and have a non-conductive baseplate that permits pc-card runs to be placed beneath the package. Units are assembled using high-speed automated SMT techniques and are fully encapsulated with thermally conductive potting compound. Every unit is electrically tested before and after encapsulation, 100% burned-in under full load, hi-pot tested, and final-electrical tested prior to shipment. Every unit meets DATEL's traditional high standards for quality and long-term reliability.

DATEL, Inc., 11 Cabot Boulevard, Mansfield, MA 02048 (U.S.A.) Tel: (508)339-3000, (800)233-2765 Fax: (508)339-6356 Email:

Typical = +25°C under nominal line voltage and full-load conditions unless otherwise noted. Ripple/Noise (R/N) measured over a 20MHz bandwidth. Balanced loads, to 100% load. Nominal line voltage, no-load/full-load conditions.

Output Configuration: B = Bipolar Wide Range Input Voltage Range: = 18-36 Volts (24V nominal) = 36-72 Volts (48V nominal)

Maximum Output Current in mA from each output
I/O Connections Pin Function P4 1 +Input 2 ­Input 3 +Output 4 Common 5 No Pin 6 ­Output

For "D24" models, the case is connected to pin 2 (­VIN). For "D48" models, the case is connected to pin 1 (+VIN).

Typical = +25°C under nominal line voltage and full-load conditions, unless noted.

Input Voltage Range: "D24" Models "D48" Models Input Current Input Filter Type Reverse-Polarity Protection VOUT Accuracy (50% load): ±5V Outputs ±12/±15V Outputs Temperature Coefficient Ripple/Noise (20MHz BW) Line Regulation Load Regulation Efficiency Isolation Voltage Current Limiting Overvoltage Protection Transient Response (50% load step) Switching Frequency Operating Temperature (ambient): Without Derating With Derating Storage Temperature Dimensions Shielding Case Connection: "D24" Models "D48" Models Case Material Pin Material Weight 18-36 Volts (24V nominal) 36-72 Volts (48V nominal) See Ordering Guide on "D24" models on "D48" models Yes (Instantaneous, 6A maximum) Input Voltage: "D24" Models "D48" Models

44 Volts 88 Volts Current must be <6A. Brief duration only. Fusing recommended. 6.8 Volts, limited duration 15 Volts, limited duration 18 Volts, limited duration Current limited. Max. current and short-circuit duration are model dependent. +125°C +300°C

Input Reverse-Polarity Protection Output Overvoltage Protection ±5V Outputs ±12V Outputs ±15V Outputs Output Current

±1.5%, maximum ±1%, maximum ±0.02% per °C See Ordering Guide See Ordering Guide See Ordering Guide See Ordering Guide 1000Vdc, minimum Auto-recovery Zener/transorb clamps

Storage Temperature Lead Temperature (soldering, 10 sec.)

These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied.

Floating Outputs Since these are isolated DC/DC converters, their outputs are "floating." Any BWR model may be configured to produce an output or 30V (for or ±15V models, respectively) by applying the load across the +Output and ­Output (pins 3 and 6), with either output grounded. The Common (pin 4) should be left open. Minimum 20% loading is recommended under these conditions. Filtering and Noise Reduction All BWR 5 Watt DC/DC Converters achieve their rated ripple and noise specifications without the use of external input/output capacitors. In critical applications, input/output ripple and noise may be further reduced by installing low-ESR, tantalum or electrolytic capacitors across the input and/or output terminals. Output capacitors should be connected between their respective output pin (pin or 6) and Common (pin 4) as shown in Figure 2. The capacitors should be located as close to the power converters as possible. Typical values are listed below. In many applications, using values greater than those listed will yield better results. To Reduce Input Ripple "D24" Models "D48" Models To Reduce Output Ripple ±5V Outputs ±12/15V Outputs 47µF, 10V, Low ESR 33µF, 20V, Low ESR

11.4mm) 5-sided Pin 2 (­VIN) Pin 1 (+VIN) Corrosion resistant steel with epoxy-based enamel finish Brass, solder coated 0.7 ounces (20 grams)

These power converters require a minimum 20% loading to maintain specified regulation. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Application-specific internal input/output filtering can be recommended and perhaps added internally on request. Contact DATEL Applications Engineering for details. Units can be screened or modified for higher guaranteed isolation voltages. Contact DATEL Applications Engineering for details. Units can be screened for lower-temperature operation. Contact DATEL Applications Engineering for details.

In critical, space-sensitive applications, DATEL may be able to tailor the internal input/output filtering of these units to meet your specific requirements. Contact our Applications Engineering Group for additional details.


Some Part number from the same manufacture Datel, Inc.
BWR-12/335-D5A 12V 7-10W, Dual Output DC/DC Converter
BWR-12/625-D5A 12V 15-20W, Dual Output DC/DC Converter
BWR-12/725-D12A DC/DC Power Converters
BWR-12/830-D12A 12V 15-20W, Dual Output DC/DC Converter
BWR-15/100-D12 12V 3W, Dual Output DC/DC Converter
BWR-15/100Series 3w, DC/DC Converter
BWR-15/165-D24 DC/DC Power Converters
BWR-15/165Series 5w, DC/DC Converter
BWR-15/275-D5A 12V 7-10W, Dual Output DC/DC Converter
BWR-15/500-D5A 12V 15-20W, Dual Output DC/DC Converter
BWR-15/575-D12A DC/DC Power Converters
BWR-15/670-D12A 12V 15-20W, Dual Output DC/DC Converter
BWR-15/85-D5 12V 3W, Dual Output DC/DC Converter
BWR-5/1500-D12A DC/DC Power Converters
BWR-5/1500-D5A 12V 15-20W, Dual Output DC/DC Converter
BWR-5/250-D12 12V 3W, Dual Output DC/DC Converter
BWR-5/250Series 3w, DC/DC Converter
BWR-5/3-3.3/4.25-D12A DC/DC Power Converters
BWR-5/500-D24 DC/DC Power Converters

ADS-942AME : 2mhz, Low Power Sampling ADC: 14-bit

DLV-3.3/6-1.2/7-D24 : DC/DC Power Converters

DLV-3.3/6-1.5/7-D12 : DC/DC Power Converters

DVME-621 : Boards->Data Acquisition

PC-414K : Boards->Data Acquisition

PCI-441A : Boards->Data Acquisition

SHM-49MC : Miniature, High-speed, 10.01% Sample-hold Amplifiers

UWR-15/335SERIES : 5w DC/DC Converter

UWR-5/4000-D48E : 12V 14-20W, Single Output DC/DC Converter

Same catergory

BQ24012DRCR : ti BQ24012, BqTINY(TM) Linear, 1-cell (4.2V) Li-ion Charger w/ 1-A Fet, ac Present & Charge Enable in QFN/MLP-10.

CS5205-2GDPR3 : 5A, 1.5V ±2% Tolerance Low Drop Out Voltage Regulator, Package: D2PAK, Pins=3.

M62212P : General Purpose DC-DC Converter. 3.0V FIXED OUTPUT VOLTAGE DC-DC CONVERTER GENERAL The is a general purpose DC-DC converter which provides a 3.0V fixed output voltage. It is possible to simplify the peripheral circuit and to design compact and low cost sets because this IC, housed in a small or 8-pin package includes necessary peripheral components. Especially this is most suitable.

MAX1999EVKIT : MAX1999EVKIT Evaluation Kit For The MAX1777/MAX1977/MAX1999. The MAX1999 evaluation kit (EV kit) demonstrates the MAX1999's standard application circuit. This DC-DC converter steps down high-voltage batteries and/or AC adapters, generating system supplies for notebook computers. The MAX1999 EV kit provides dual 5V and 3.3V output voltages from to 24V battery input range. It delivers to 5A output current for the 5V output.

MAX622 : High-side Power Supplies.

MM1412 : Protection of Lithium Ion Battery. This IC protects lithium ion batteries in the event of overcharge, overdischarge and overcurrent. It has the following two functions: an overcurrent detection function that turns the external FET-SW off when a problem occurs during charging, etc. and excess voltage is impressed on each battery for longer than a certain time, and an overdischarge detection.

NJU7708 : Voltage Detector With Delay Function. GENERAL The is a low quiescent current voltage detector with delay function featuring high precision detection voltage. The detection voltage is fixed internally with an accuracy NJU7708 is Nch. Open Drain and NJU7709 of output circuit form is a C-MOS output. PACKAGE OUTLINE High Precision detection Voltage ±1.0% Low Quiescent Current 1.3µA Detection.

PT7715A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT7715, 20-A 1.075V to 1.85V 5V-Input Programmable Isr.

SC2595 : Sink/Source Regulators. Integrated Linear DDR Termination Regulator. The is an integrated linear DDR termination device, which provides a complete solution for DDR termination designs; while meeting the JEDEC requirements of SSTL-2 and SSTL-3 s for DDR-SDRAM termination. The SC2595 can source and sink 1.5A current at the output VTT to within 1% or less, while regulating an output voltage equal to VDDQ/2. VTT is designed.

UCC27425D : MOSFET and Power Drivers. ti UCC27425, Dual 4-A MOSFET Driver With Enable.

UCC2804 : Current Mode PWM Controllers. Low-power Bicmos Current-mode PWM. 100µA Typical Starting Supply Current 500µA Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A.

UCC384 : 12 - Low Dropout (LDO) 0.5A Negative Linear Regulator. Regulation 0.2 V Dropout 0.5 A Wide Input Voltage Range ­15 V Low Quiescent Current Irrespective of Load Simple Logic Shutdown Interfacing ­12 V, and Adjustable Output 2.5% Duty Cycle Short Circuit Protection The UCC384-x family of negative linear-series pass regulators is tailored for low-dropout applications where low-quiescent power is important.

X80142 : Hotswap & Power Sequencers. Voltage Supervisor/sequencerquad Programmable Time Delay With Local/remote Voltage Monitors.

FAN3224C : Dual 4A High-Speed, Low-Side Gate Driver The FAN3223-25 family of dual 4A gate drivers is designed to drive N-channel enhancement-mode MOSFETs in low-side switching applications by providing high peak current pulses during the short switching intervals. The driver is available with either TTL or CMOS input thresholds. Internal circuitry provides an under-voltage.

LTC2919CMS-2.5#PBF : Precision Triple/Dual Input UV, OV And Negative Voltage Monitor The LTC2919 is a triple/dual input monitor intended for a variety of system monitoring applications. Polarity selection and a buffered reference output allow the LTC2919 to monitor positive and negative supplies for undervoltage (UV) and overvoltage (OV) conditions. The two adjustable inputs.

ISL6263D : 3-Bit VID Single-Phase Voltage Regulator With Current Monitor For GPU Core Power The ISL6263D IC is a Single-Phase Synchronous Buck PWM voltage regulator for GPU core power applications. It Intersil’s Robust Ripple Regulator (R3) Technology™. Integrated current monitor, differential remote sense amplifier, MOSFET driver and bootstrap diode result in smaller.

LTC4265 : IEEE 802.3 At High Power PD Interface Controller With 2-Event Classification Recognition The LTC4265 is a 3rd generation Powered Device (PD) Interface controller intended for IEEE 802.3at high power Power-over-Ethernet (PoE) applications up to 25.5W. By supporting 1-event and 2-event classification signaling as defined by IEEE 802.3, the LTC4265 can be used.

S-1167B15-I6T2G : ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR The S-1167 Series is a positive voltage Regulator with ultra low current consumption, high ripple rejection, low drop voltage and high output voltage accuracy developed based on CMOS technology. Although current consumption is very small with 9 A typ., S-1167.

PT7M7812STB : µ µ µ µ µP Supervisor Circuits The PT7M7xxx family microprocessor (µP) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in µP systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions..

0-C     D-L     M-R     S-Z