Details, datasheet, quote on part number: MBM29DL322TE80PBT
Description8M (1M X 8/512k X 16) BIT
CompanyFujitsu Microelectronics, Inc.
DatasheetDownload MBM29DL322TE80PBT datasheet


Features, Applications

Single 3.0 V read, program, and erase Minimizes system level power requirements Simultaneous operations Read-while-Erase or Read-while-Program Compatible with JEDEC-standard commands Uses same software commands as E2PROMs Compatible with JEDEC-standard world-wide pinouts (Pin compatible with MBM29LV800TA/BA) 48-pin TSOP(I) (Package suffix: PFTN Normal Bend Type, PFTR Reversed Bend Type) 48-ball FBGA (Package suffix: PBT) Minimum 100,000 program/erase cycles High performance 70 ns maximum access time Sector erase architecture Two 16K byte, four 8K bytes, two 32K byte, and fourteen 64K bytes. Any combination of sectors can be concurrently erased. Also supports full chip erase. Boot Code Sector Architecture T = Top sector B = Bottom sector Embedded EraseTM Algorithms Automatically pre-programs and erases the chip or any sector Embedded ProgramTM Algorithms Automatically writes and verifies data at specified address Data Polling and Toggle Bit feature for detection of program or erase cycle completion Ready/Busy output (RY/BY) Hardware method for detection of program or erase cycle completion Automatic sleep mode When addresses remain stable, automatically switch themselves to low power mode. Low VCC write inhibit 2.5 V Erase Suspend/Resume Suspends the erase operation to allow a read in another sector within the same device

Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc.

(Continued) Sector protection Hardware method disables any combination of sectors from program or erase operations Sector Protection Set function by Extended sector protection command Fast Programming Function by Extended Command Temporary sector unprotection Temporary sector unprotection via the RESET pin.

The MBM29DL800TA/BA are 8M-bit, 3.0 V-only Flash memory organized as 1M bytes of 8 bits each or 512K words of 16 bits each. The MBM29DL800TA/BA are offered a 48-pin TSOP(I) and 48-ball FBGA packages. These devices are designed to be programmed in-system with the standard system 3.0 V VCC supply. 12.0 V VPP and 5.0 V VCC are not required for write or erase operations. The devices can also be reprogrammed in standard EPROM programmers. MBM29DL800TA/BA provides simultaneous operation which can read a data while program/erase. The simultaneous operation architecture provides simultaneous operation by dividing the memory space into two banks. The device can allow a host system to program or erase in one bank, then immediately and simultaneously read from the other bank. The standard MBM29DL800TA/BA offer access times 70 ns and 120 ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention the devices have separate chip enable (CE), write enable (WE), and output enable (OE) controls. The MBM29DL800TA/BA are pin and command set compatible with JEDEC standard E2PROMs. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the devices is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29DL800TA/BA are programmed by executing the program command sequence. This will invoke the Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an internal algorithm that automatically preprograms the array it is not already programmed before executing the erase operation. During erase, the devices automatically time the erase pulse widths and verify proper cell margin. A sector is typically erased and verified in 1.0 second. (If already completely preprogrammed.) The devices also feature a sector erase architecture. The sector mode allows each sector to be erased and reprogrammed without affecting other sectors. The MBM29DL800TA/BA are erased when shipped from the factory. The devices feature single 3.0 V power supply operation for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. A low VCC detector automatically inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling DQ7, by the Toggle Bit feature DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been completed, the devices internally reset to the read mode. Fujitsu's Flash technology combines years of EPROM and E2PROM experience to produce the highest levels of quality, reliability, and cost effectiveness. The MBM29DL800TA/BA memories electrically erase the entire chip or all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word at a time using the EPROM programming mechanism of hot electron injection.


Related products with the same datasheet
Some Part number from the same manufacture Fujitsu Microelectronics, Inc.
MBM29DL322TE80TN 8M (1M X 8/512k X 16) BIT
FCN-560 Microsd/tf Card Connector
MB91260B 32-bit Proprietary Microcontroller CMOS
MB3800_06 Switching Regulator Controller (Low Voltage)
MB90F362 16-bit Proprietary Microcontroller
MB3730A 14W BTL Audio Power Amplifier
CE71LE 0.25um CMOS Technology
MB89560A 8-bit Proprietary Microcontroller CMOS
MB87002 1200 BPS MSK Modem
F124JB 8-bit Microcontrollers
MB91V245A 32-bit Microcontroller
CE66P3 0.35um CMOS Technology

FAR-C3SB-06000-J01-T : Piezoelectric Resonator

FAR-C4CN-09830-L02-R : Piezoelectric Resonator (4 to 23.9 MHz)

FAR-C4SB-11059-M02-T : Piezoelectric Resonator

FBR582ND24Y : Compact Power Relay 1 POLE X 2-12a (28vdc) (FOR 24V Battery Automotive Applications)

MB89983-XXX-PFM : 8-bit Proprietary Microcontroller

C1608JB0J475K : 2-ch Dc/dc Converter IC

FMW21N60GSC-K1 : 21 A, 600 V, 0.37 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-247AA Specifications: Polarity: N-Channel ; MOSFET Operating Mode: Enhancement ; V(BR)DSS: 600 volts ; rDS(on): 0.3700 ohms ; PD: 2500 milliwatts ; Package Type: TO-247, TO-247, 3 PIN ; Number of units in IC: 1

MB3800PF-XXX : SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO8 Specifications: Configuration / Function: SINGLE ; Package Type: Other, 5.30 X 6.35 MM, 2.25 MM HEIGHT, 1.27 MM PITCH, PLASTIC, SOP-8 ; Life Cycle Stage: ACTIVE ; VIN: 2 volts ; fsw: 1000 kHz ; Operating Temperature: -30 to 85 C (-22 to 185 F)

MB90F583CPMC : MICROCONTROLLER, PQFP100 Specifications: Life Cycle Stage: ACTIVE ; Package Type: LFQP, Other, 14 X 14 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-100 ; Pin Count: 100

MB91F213PMC-GSE1 : 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 40 MHz ; ROM Type: Flash ; Supply Voltage: 3.5 to 5.5 volts ; I/O Ports: 82 ; Package Type: LFQP, Other, 14 X 14 MM, 1.70 HEIGHT, 0.50 PITCH, PLASTIC, LQFP-100 ; Operating Range: Industrial ; Pin Count: 100 ; Operating Temperature: -40 to 105 C

MB96F348CSCPMC-GSE2 : 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100 Specifications: Data Bus: 16 Bit ; Life Cycle Stage: ACTIVE ; Clock Speed: 56 MHz ; ROM Type: Flash ; Supply Voltage: 3 to 5.5 volts ; I/O Ports: 80 ; Package Type: QFP, Other, 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, QFP-100 ; Operating Range: Auto ; Pin Count: 100 ; Operating Temperatur

0-C     D-L     M-R     S-Z