Details, datasheet, quote on part number: IDT7006S25FB
PartIDT7006S25FB
CategoryMemory => Memory Chips => 6477019
Title16K X 8 DUAL-PORT SRAM, 15 ns, PQFP68
Description
CompanyIntegrated Device Technology, Inc.
DatasheetDownload IDT7006S25FB datasheet
Quote
Find where to buy
 
Specifications 
Memory CategorySRAM Chip
Density131 kbits
Number of Words16 k
Bits per Word8 bits
Package Type0.970 X 0.970 INCH, 0.080 INCH HEIGHT, GREEN, FP-68
Pins68
Logic FamilyCMOS
Supply Voltage5V
Access Time15 ns
Operating Temperature0 to 70 C (32 to 158 F)

 

Features, Applications
Features

True Dual-Ported memory cells which allow simultaneous reads of the same memory location High-speed access ­ Military: 20/25/35/55/70ns (max.) ­ Industrial: 55ns (max.) ­ Commercial: 15/17/20/25/35/55ns (max.) Low-power operation ­ IDT7006S Active: 750mW (typ.) Standby: 5mW (typ.) ­ IDT7006L Active: 700mW (typ.) Standby: 1mW (typ.) IDT7006 easily expands data bus width to 16 bits or more using the Master/Slave select when cascading more than one device

M/S = H for BUSY output flag on Master, M/S = L for BUSY input on Slave Busy and Interrupt Flags On-chip port arbitration logic Full on-chip hardware support of semaphore signaling between ports Fully asynchronous operation from either port Devices are capable of withstanding greater than 2001V electrostatic discharge Battery backup operation--2V data retention TTL-compatible, single 5V (±10%) power supply Available in 68-pin PGA, quad flatpack, PLCC, and a 64-pin TQFP Industrial temperature range +85°C) is available for selected speed Green parts available, see ordering information

NOTES: 1. (MASTER): BUSY is output; (SLAVE): BUSY is input. 2. BUSY outputs and INT outputs are non-tri-stated push-pull.

Description

The is a high-speed x 8 Dual-Port Static RAM. The IDT7006 is designed to be used as a stand-alone 128K-bit Dual-Port RAM as a combination MASTER/SLAVE Dual-Port RAM for 16-bit-or-more word systems. Using the IDT MASTER/SLAVE Dual-Port RAM approach 16-bit or wider memory system applications results in full-speed, errorfree operation without the need for additional discrete logic. This device provides two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature controlled by CE permits the on-chip circuitry of each port to enter a very low standby power mode. Fabricated using IDT's CMOS high-performance technology, these devices typically operate on only 750mW of power. Low-power (L) versions offer battery backup data retention capability with typical power consumption of 500µW from a 2V battery. The IDT7006 is packaged in a ceramic 68-pin PGA, an 68-pin quad flatpack, a PLCC, and a 64-pin thin quad flatpack, TQFP. Military grade product is manufactured in compliance with the latest revision of MIL-PRF38535 QML, Class B, making it ideally suited to military temperature applications demanding the highest level of performance and reliability.

NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground supply. 3. J68-1 package body in x.95 in. x.17 in. F68-1 package body in x.08 in. PN64-1 package body is approximately 1.4mm. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking


NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground supply. 3. Package body is approximately in x.16 in. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking

Left Port CEL R/WL OEL - I/O7L SEML INTL BUSYL CER R/WR OER - I/O7R SEMR INTR BUSYR M/S VCC GND Right Port Chip Enable Read/Write Enable Output Enable Address Data Input/Output Semaphore Enable Interrupt Flag Busy Flag Master or Slave Select Power Ground


 

Related products with the same datasheet
IDT7006S15G
IDT7006S15GG
IDT7006S15J
IDT7006S15J8
IDT7006S15JG
IDT7006S15PF
IDT7006S15PF8
IDT7006S15PF9
IDT7006S15PFG
IDT7006S17
IDT7006S17F
IDT7006S17FG
Some Part number from the same manufacture Integrated Device Technology, Inc.
IDT7006S25FG Specifications: Memory Category: SRAM Chip ; Density: 131 kbits ; Number of Words: 16 k ; Bits per Word: 8 bits ; Package Type: 0.970 X 0.970 INCH, 0.080 INCH HEIGHT, GREEN, FP-68 ; Pins: 68 ; Logic Family:
IDT7007L15GG Specifications: Memory Category: SRAM Chip ; Density: 262 kbits ; Number of Words: 32 k ; Bits per Word: 8 bits ; Package Type: 1.800 X 1.800 INCH, 0.160 INCH HEIGHT, GREEN, PGA-68 ; Pins: 68 ; Logic Family:

IDT54FCT166245CT : Fast CMOS 16-bit Bidirectional Transceivers

IDT70125L-45 : Multiport->16K Dual-port RAM Master: 2kx9

IDT7206L120D : CMOS Asynchronous Fifo 2048 X 9, 4096 X 9, 8192 X 9 And 16384 X 9

IDT72845LB20PFI : CMOS DUAL Asynchronous FIFO DUAL 256 x 9, DUAL 512 x 9,dual 1,024 x 9, DUAL 2,048 x 9,dual 4,096 x 9, DUAL 8,192 x 9

IDT71V3578YS133BGI : 128K X 36, 256K X 18 3.3V Synchronous Srams 3.3V I/O, Flow-through Outputs Burst Counter, Single Cycle Deselect

IDT7142LA55L48G : HIGH SPEED 2K X 8 DUAL PORT STATIC RAM The IDT7132/IDT7142 are high-speed 2K x 8 Dual-Port Static RAMs. The IDT7132 is designed to be used as a stand-alone 8-bit Dual-Port RAM or as a “MASTER� Dual-Port RAM together with the IDT7142 “SLAVE� Dual-Port in 16-bit-or-more word width systems.

IDT7142LA25L48G : HIGH SPEED 2K X 8 DUAL PORT STATIC RAM The IDT7132/IDT7142 are high-speed 2K x 8 Dual-Port Static RAMs. The IDT7132 is designed to be used as a stand-alone 8-bit Dual-Port RAM or as a “MASTER” Dual-Port RAM together with the IDT7142 “SLAVE” Dual-Port in 16-bit-or-more word width systems. Using

IDT71V124SA15PHGI : 3.3V CMOS Static RAM 1 Meg (128k x 8-bit) Center Power & Ground Pinout

IDT7024S20J8 : Multi-Ports 4K X 16 Dual-port RAM

IDT723613L20PQFI9 : 64 X 36 OTHER FIFO, 10 ns, PQFP120 Specifications: Memory Category: FIFO ; Density: 2 kbits ; Number of Words: 64 k ; Bits per Word: 36 bits ; Package Type: TQFP, TQFP-120 ; Pins: 120 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 10 ns ; Cycle Time: 15 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

 
0-C     D-L     M-R     S-Z