Details, datasheet, quote on part number: MSK-0021FP
PartMSK-0021FP
Category
DescriptionHIGH Power Op-amp
CompanyM.S. Kennedy
DatasheetDownload MSK-0021FP datasheet
  

 

Features, Applications

Available as SMD #5962-8508701 Output Current - 0.5 Amps Peak Low Power Consumption-Class C Design Programmable Current Limit High Slew Rate Continuous Output Short Circuit Duration Replacement for LH0041 Available in a surface mount package MSK0041FP MSK0041

The MSK 0041 and 0041FP are general purpose Class C power operational amplifiers. These amplifiers offer high output currents, making them an excellent low cost choice for motor drive circuits. The amplifier and load can be protected from fault conditions through the use of internal current limit circuitry that can be user programmed with two external resistors. These devices are also compensated with a single external capacitor. The MSK 0041 is available in a hermetically sealed 12 pin TO-8 package. The MSK 0041FP is packaged a 12 pin hermetic metal flatpack.

Servo Amplifer Motor Driver Audio Amplifier Programmable Power Supply

MSK0041 1 ISC+ 2 Compensation 3 GND NC 5 -Input 6 +Input 7 Balance 8 Balance 9 ISC10 -VCC 11 Output 12 +VCC (PIN NUMBERS ARE FOR FP 1 GND 2 Balance 3 -Input 4 +Input 5 Balance NC 7 -VCC 8 ISC9 Output 10 ISC+ 11 +VCC 12 Compensation

VCC IOUT VIN RTH Supply Voltage Peak Output Current Differential Input Voltage Common Mode Input Voltage Thermal Resistance-Junction to Case MSK 0041 MSK 0041FP


Storage Temperature Range Lead Temperature Range (10 Seconds) Junction Temperature Case Operating Temperature Range Military Versions (H/B/E) Industrial Versions


STATIC Supply Voltage Range Quiescent Current Power Consumption INPUT Input Offset Voltage Input Bias Current Input Offset Current Input Capacitance Input Resistance

Common Mode Rejection Ratio Power Supply Rejection Ratio Input Noise Voltage OUTPUT Output Voltage Swing

RSC = 3.3 VOUT = MAX Output Short Circuit Current Settling Time 0.1% 2V step TRANSFER CHARACTERISTICS Slew Rate VOUT 100 3 Open Loop Voltage Gain Transition Times Overshoot = 1K

Unless otherwise specified, VCC = 3000pF. Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices (B/H suffix) shall be 100% tested to subgroups 2, 3 and 4. Subgroup = +25C Subgroup = +125C Subgroup = -55C Reference DSCC SMD 5962-8508701 for electrical specifications for devices purchased as such. Subgroup 5 and 6 testing available upon request.

To select the correct heat sink for your application, refer to the thermal model and governing equation below.

The MSK 0041 has an on-board current limit scheme designed to limit the output drivers anytime output current exceeds a predetermined limit. The following formula may be used to determine the value of the current limit resistance necessary to establish the desired current limit. 0.7 ISC

PD x (RJC + RCS + RSA) + TA Where TJ PD RJC RCS RSA TA TS Junction Temperature Total Power Dissipation Junction to Case Thermal Resistance Case to Heat Sink Thermal Resistance Heat Sink to Ambient Thermal Resistance Case Temperature Ambient Temperature Sink Temperature See "Application Circuits" in this data sheet for additional information on current limit connections.

In our example the amplifier application requires the output to drive a 10 volt peak sine wave across a 100 ohm load for 0.1 amp of output current. For a worst case analysis we will treat the 0.1 amp peak output current as a D.C. output current. The power supplies are 15 VDC. 1.) Find Power Dissipation PD=[(quiescent current) X (+VCC - (VCC))] + [(VS - VO) X IOUT] =(3.5 mA) =0.6W 2.) For conservative design, set +150C. 3.) For this example, worst case +25C. 4.) RJC 85C/W 5.) Rearrange governing equation to solve for RSA: RSA = (TJ - TA) PD - (RJC) - (RCS) = 123C/W The heat sink in this example must have a thermal resistance of no more than 123C/W to maintain a junction temperature of less than +150C. This calculation assumes a case to sink thermal resistance 0.15C/W. 3

Both the negative and the positive power supplies must be effectively decoupled with a high and low frequency bypass circuit to avoid power supply induced oscillation. An effective decoupling scheme consists a 0.1 microfarad ceramic capacitor in parallel with a 4.7 microfarad tantalum capacitor from each power supply pin to ground.This capacitor will eliminate any peak output voltage clipping which may occur due to poor power supply load regulation. All power supply decoupling capacitors should be placed as close to the package power supply pins as possible.

The safe operating area curve is a graphical representation of the power handling capability of the amplifier under various conditions. The wire bond current carrying capability, transistor junction temperature and secondary breakdown limitations are all incorporated into the safe operating area curves. All applications should be checked against the curves to ensure high M.T.B.F. Rev. - 4/02


 

Related products with the same datasheet
MSK-0041
Some Part number from the same manufacture M.S. Kennedy
MSK-0041 HIGH Power Op-amp
MSK032E FET Input Differential Op-amp
MSK106HRHG Radiation Hardened HIGH Power Op-amp
BBF2815 20W Dc-dc Converters
MSK738B Inverting Operational Amplifier
MSK5100-00B Msk5102-3.3h LOW Dropout Voltage Regulators
MSK5250-1.5E VERY HIGH Current, LOW Dropout Surface Mount Voltage Regulators
MSK707E Ultra-accurate/high SLEW RATE Inverting Operational Amplifier
MSK4460D 10 AMP, 55V, 3 Phase Mosfet Brushless Motor Controller
MSK5920-1.5ERHD RAD Tolerant Ultra LOW Dropout Adjustable Positive Linear Regulator

MSK0024 : Operational Amplifier, Replacement For LH0024

MSK4301HD : 29 Amp, 75v, 3 Phase MOSFET Bridge With Intelligent Integrated Gate Drive

MSK5115-3.3ZU : Linear Voltage Regulator, 5 Pin Power, Top or Z-tab

MSK643B : Wide Bandwidth, Very High Voltage CRT Video Amplifier

MSK5250-1.7H : VERY HIGH Current, LOW Dropout Surface Mount Voltage Regulators

DHC2803SH : 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE Specifications: Package Type: DIP, Other, 1 X 1 INCH, 0.350 INCH HEIGHT, HERMETIC SEALED, DIP-8 ; Output Voltage: 3.2 to 3.4 volts ; Input Voltage: 12 to 50 volts ; Output Power: 5 watts (0.0067 HP) ; Operating Temperature: -55 to 125 C (-67 to 257 F)

MSK5203TU : DUAL OUTPUT, FIXED MIXED LDO REGULATOR, SFM5 Specifications: Regulator Type: Low Dropout ; Output Voltage Type: Fixed ; Package Type: Other, TOP TAB, BENT DOWN, 5 PIN ; Life Cycle Stage: ACTIVE ; Output Voltage: 11.76 to 12.24 volts ; IOUT: 3 amps ; VIN: 13 to 26 volts ; Dropout Voltage: 0.6000 volts

MSK5922-1.9ERHD : 1.5 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PSFM5 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, HERMATIC SEALED, BENT DOWN, SIP-5 ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.44 to 1.56 volts ; IOUT: 5 amps ; VIN: 2 to 6.5 volts ; Dropout Voltage: 0.4000 volts

Same catergory

MHW7185A : . High Output Power Doubler 750 MHz CATV Amplifiers Designed specifically for 750 MHz CATV applications. ion implanted, arsenic emitter transistors with an all gold metallization system. Supply Voltage = 24 Vdc 6th Generation Die Technology Specified for 110 Channel Performance Broadband Power Gain = 50 MHz 18 dB Min 19.5 dB Min (MHW7205A) Broadband.

8327 : Rj-45 1000 Base-t Magnetics. Meets IEEE 802.3 and ANSI X3.263 requirements including 350H OCL with 8mA DC bias For use with Broadcom BCM5401, BCM5402 and the Marvell 88E1000 Gigabit phy transceivers Includes integrated LEDs. LED signal leads are isolate from the Ethernet signal leads to reduce EMI and crosstalk Contact Plating: 6u-inch gold flashed Turns Ratio: : 1CT:1CT3% Inductance:.

SN5404_04 : HEX Inverters. SN5404. J PACKAGE OR W PACKAGE OR NS PACKAGE SN74LS04. D, DB, OR NS PACKAGE (TOP VIEW) - No internal connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA.

354902-GY : Fuse Blocks and Clips. 3AG OMNI-BLOK Molded Base Type Fuse Block A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The unique design permits self-alignment of clips to fuse cap. This, plus a one-piece clip/terminal assures low contact resistance. Higher current.

DS_K1S161611A : 1mx16 bit Uni-transistor Random Access Memory. 0.0 0.1 Initial Draft Revised - Added Lead Free 48-FBGA-6.00x7.00 Product The attached datasheets are provided by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the s and products. SAMSUNG Electronics will answer to your questions about device. If you have any questions, please contact the SAMSUNG branch offices. The K1S161611A.

2944-0 : BANANA PLUG, 5A, SCREW, BLACK. s: Connector Type: Banana Plug ; Series: - ; Gender: Plug ; Contact Termination: Screw ; Current Rating: 5A ; Voltage Rating: 2.5kV ; Contact Plating: Gold ; Contact Material: Brass ; Connector Color: Black ; Connector Mounting: Cable.

ECO-S2DP821CA : 820F Aluminum Capacitor Radial, Can - Snap-In 200V; CAP ALUM 820UF 200V 20% SNAP. s: Capacitance: 820F ; ESR (Equivalent Series Resistance): 222.0 mOhm ; : General Purpose ; Lifetime @ Temp.: 3000 Hrs @ 85C ; Size / Dimension: 0.984" Dia (25.00mm) ; Lead Spacing: 0.394" (10.00mm) ; Surface Mount Land Size: - ; Mounting Type: Through Hole ; Package.

CAS 15-NP : CURRENT TRANSDUCER, 15A. s: Current Measuring Range AC: -51A to 51A ; Current Measuring Range DC: -51A to 51A ; Operating Pressure Range: - ; Operating Frequency Range: - ; Supply Voltage Range DC: 4.75V to 5.25V ; Sensor Output: Voltage ; Accuracy %: 0.8% ; Response Time: 0.3s.

W2151001JALF : Wirewound Resistors - Through Hole 1K 5watt 5%. s: Manufacturer: IRC ; Product Category: Wirewound Resistors - Through Hole ; RoHS:  Details ; Resistance: 1 KOhm ; Tolerance: 5 % ; Power Rating: 5 Watts ; Temperature Coefficient: 75 PPM / C ; Series: W20 ; Termination Style: Axial ; Operating Temperature Range: - 55 C to + 350 C ; Dimensions: 7 mm Dia.

BFC233820154 : 0.15F Film Capacitor Radial; CAP FILM 0.15UF 630VDC RADIAL. s: Capacitance: 0.15F ; Tolerance: 20% ; Dielectric Material: Polypropylene, Metallized ; Package / Case: Radial ; Packaging: Bulk ; Lead Spacing: 0.591" (15.00mm) ; ESR (Equivalent Series Resistance): - ; Mounting Type: Through Hole ; : EMI Suppression ; Lead Free Status: Lead Free ; RoHS.

D38999/26WH55PNL : Aluminum, Olive Drab Cadmium Plated Free Hanging (In-Line) Circular - Housing Connectors, Interconnect Plug for Male Contacts; CONN HSG PLUG 55POS STRGHT PINS. s: : Shielded ; Packaging: Bulk ; Connector Type: Plug for Male Contacts ; Mounting Type: Free Hanging (In-Line) ; Shell Size - Insert: 23-55 ; Contact Type: Crimp ; Fastening Type: Threaded.

AIUR-04-101J : Fixed Inductors, Coils, Choke 100H 200mA Radial Ferrite Core; INDUCTOR POWER 100UH 5% T/H. s: Inductance: 100H ; Tolerance: 5% ; Package / Case: Radial ; Packaging: Bulk ; Type: Ferrite Core ; Current: 200mA ; Mounting Type: Through Hole ; Q @ Freq: 80 @ 796kHz ; Frequency - Self Resonant: 5.3MHz ; DC Resistance (DCR): 2 Ohm Max ; Shielding: Unshielded.

PIC16F610-I/ML : Embedded - Microcontroller Integrated Circuit (ics) Internal Tube 2 V ~ 5.5 V; IC PIC MCU FLASH 1KX14 16QFN. s: Program Memory Size: 1.75KB (1K x 14) ; RAM Size: 64 x 8 ; Number of I /O: 11 ; Package / Case: 16-VQFN Exposed Pad ; Speed: 20MHz ; Oscillator Type: Internal ; Packaging: Tube ; Program Memory Type: FLASH ; EEPROM Size: - ; Core Processor:.

SG7812AK : Pmic - Voltage Regulator - Linear Integrated Circuit (ics); IC VOLTAGE REG POS 12V TO-3. s: Lead Free Status: Lead Free Compliant by Exemption ; RoHS Status: RoHS Compliant by Exemption.

CRB2A4E393JT : Resistor 39K Ohm 62.5mW 4 Resistors[number of pins] Pin Networks, Arrays; RES ARRAY 39K OHM 4 RES 0804. s: Resistance (Ohms): 39K ; Tolerance: 5% ; Power Per Element: 62.5mW ; Circuit Type: Isolated ; Number of Pins: 8 ; Packaging: Tape & Reel (TR) ; Number of Resistors: 4 ; Package / Case: 0804 (2010 Metric), Concave ; Mounting Type: Surface Mount.

MP20249DC-MC-LF : FIXED POSITIVE LDO REGULATOR. s: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Life Cycle Stage: ACTIVE.

CC3000BOOST : WiFi / 802.11 Development Tools BoosterPack. s: Manufacturer: Texas Instruments ; Product Category: WiFi / 802.11 Development Tools ; Product: Evaluation Boards ; Tool Is For Evaluation Of: CC3300 ; Protocol Supported: 802.11 b/g ; Interface Type: RS-232, SPI ; For Use With: CC3300 ; Maximum Operating Temperature: + 70 C ; Minimum Operating Temperature:.

 
0-C     D-L     M-R     S-Z