Details, datasheet, quote on part number: MAX2620E/D
PartMAX2620E/D
CategoryCommunication => Wireless
Description10mhz to 1050mhz Integrated RF Oscillator With Buffered Outputs
CompanyMaxim Integrated Products
DatasheetDownload MAX2620E/D datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Low-Phase-Noise Oscillator: -110dBc/Hz (25kHz offset from carrier) Attainable Operates from Single to +5.25V Supply Low-Cost Silicon Bipolar Design Two Output Buffers Provide Load Isolation Insensitive to Supply Variations Low, 27mW Power Consumption (VCC = 3.0V) Low-Current Shutdown Mode: 0.1A (typ)

The MAX2620 combines a low-noise oscillator with two output buffers in a low-cost, plastic surface-mount, ultra-small MAX package. This device integrates functions typically achieved with discrete components. The oscillator exhibits low-phase noise when properly mated with an external varactor-tuned resonant tank circuit. Two buffered outputs are provided for driving mixers or prescalers. The buffers provide load isolation to the oscillator and prevent frequency pulling due to load-impedance changes. Power consumption is typically just 27mW in operating mode (VCC = 3.0V), and drops to less than 0.3W in standby mode. The MAX2620 operates from a single to +5.25V supply.

Analog Cellular Phones Digital Cellular Phones 900MHz Cordless Phones 900MHz ISM-Band Applications Land Mobile Radio Narrowband PCS (NPCS)

PART MAX2620EUA MAX2620E/D TEMP RANGE to +85C PIN-PACKAGE 8 MAX Dice*
*Dice are tested +25C, DC parameters only. Pin Configuration appears at end of data sheet.

VCC C17 1.5pF VTUNE 1k D1 ALPHA SMV1204-34 CERAMIC RESONATOR 1pF 4 SHDN BIAS SUPPLY 1 VCC1 OUT 8 1.5pF VCC

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.

to +6V TANK, SHDN GND.................................-0.3V to (VCC + 0.3V) OUT, OUT to GND...........................(VCC 0.6V) to (VCC + 0.3V) FDBK to GND..................................(VCC 2.0V) to (VCC + 0.3V) Continuous Power Dissipation (TA = +70C) MAX (derate 5.7mW/C above +70C).....................457mW Operating Temperature Range to +85C Junction Temperature......................................................+150C Storage Temperature to +165C Lead Temperature (soldering, 10s).................................+300C

Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

to +5.25V, FDBK = open, TANK = open, OUT and OUT connected to VCC through 50, SHDN to +85C, unless otherwise noted. Typical values measured = +25C.) (Note 1) PARAMETER Supply Current Shutdown Current Shutdown Input Voltage High Shutdown Input Voltage Low Shutdown Bias Current High Shutdown Bias Current Low SHDN = 2.0V SHDN 0.6V 5.5 SHDN = 0.6V CONDITIONS MIN TYP 9.0 0.1 MAX 12.5 2 UNITS V A

Note 1: Specifications are production tested and guaranteed = +25C and = +85C. Specifications are guaranteed by design and characterization = -40C.

(Test Circuit of Figure = +3.0V, SHDN , Z LOAD = Z SOURCE (50 f TEST = +25C, unless otherwise noted.) PARAMETER Frequency Range Reverse Isolation Output Isolation CONDITIONS to +85C (Note 2) OUT or OUT to TANK; OUT, OUT driven = -20dBm OUT to OUT MIN 50 33 TYP MAX 1050 UNITS MHz dB

Note 2: Guaranteed by design and characterization 650MHz, 900MHz, and 1050MHz. Over this frequency range, the magnitude of the negative real impedance measured at TANK is greater than one-tenth the magnitude of the reactive impedances at TANK. This implies proper oscillator start-up when using an external resonator tank circuit with 10. C3 and C4 must be tuned for operation at the desired frequency.

TYPICAL OPERATING CIRCUIT PERFORMANCE--900MHz Band CeramicResonator-Based Tank

(Typical Operating Circuit, VCC = +3.0V, VTUNE = 1.5V, SHDN = VCC, load at OUT = 50, load at OUT L1 = coaxial ceramic resonator: Trans-Tech = +25C, unless otherwise noted.) PARAMETER Tuning Range Phase Noise VTUNE to 3.0V SSB = 25kHz SSB 300kHz At OUT (Note 2) Output Power (Single-Ended) At OUT, per test circuit of Figure to +85C (Note 3) At OUT (Note 3) Noise Power Average Tuning Gain Second-Harmonic Output Load Pull Supply Pushing VSWR = 1.75:1, all phases VCC stepped from -11 -16 CONDITIONS MIN TYP dBm/Hz MHz/V dBc kHzP-P kHz/V dBm MAX UNITS MHz dBc/Hz

TYPICAL OPERATING CIRCUIT PERFORMANCE--900MHz Band Inductor-Based Tank

(Typical Operating Circuit, VCC = +3.0V, VTUNE = 1.5V, SHDN = VCC, load at OUT = 50, load at OUT = 5nH (Coilcraft = +25C, unless otherwise noted.) PARAMETER Tuning Range Phase Noise VTUNE to 3.0V SSB = 25kHz SSB 300kHz At OUT (Note 2) Output Power (single-ended) At OUT, per test circuit of Figure to +85C (Note 3) At OUT (Note 3) Noise Power Average Tuning Gain Second-Harmonic Output Load Pull Supply Pushing VSWR = 1.75:1, all phase angles VCC stepped from -11 -16 CONDITIONS MIN TYP dBm/Hz MHz/V dBc kHzP-P kHz/V dBm MAX UNITS MHz dBc/Hz


 

Related products with the same datasheet
MAX2620EUA
Some Part number from the same manufacture Maxim Integrated Products
MAX2620EUA 10mhz to 1050mhz Integrated RF Oscillator With Buffered Outputs
MAX2620EVKIT Evaluation Kit: Max2620
MAX2622 Fully Monolithic 900mhz Sige Vco in 8-pin Umax
MAX2622EVKIT Evaluation Kits
MAX2623 Fully Monolithic 900mhz Sige Vco in 8-pin Umax
MAX2623EVKIT Evaluation Kits
MAX2624 Fully Monolithic 900mhz Sige Vco in 8-pin Umax
MAX2624EVKIT Evaluation Kits
MAX262A P Programmable, Universal Switched Capacitor Filter
MAX262BENG Microprocessor Programmable Universal Active Filters
MAX262BM P Programmable, Universal Switched Capacitor Filter
MAX263 -
MAX2630 VHF-to-microwave, +3v, General-purpose Amplifiers
MAX2632EUK-T
MAX2633
MAX263AC -
MAX263ACPI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263AM -
MAX263AMJI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263BC -
MAX263BCPI VHF-to-microwave, +3v, General-purpose Amplifiers

DS1921L-F5X : Thermochron Ibutton

MAX197BMYI : Multi-range ( 10V, 5V, +10V, +5V), Single +5V, 12-Bit Das With 8+4 Bus Interface

MAX4265ESA : Ultra-low-distortion, Single-supply, 300mhz op Amps With Enable

MAX519AEPE : 2-wire Serial 8-bit DACs With Rail-to-rail Outputs

MAX209CNG : +5V, RS-232 Transceivers With 0.1F External Capacitors The MAX200MAX209/MAX211/MAX213 transceivers are designed for RS-232 and V.28 communication interfaces where 12V supplies are not available. On-board charge pumps convert the +5V input to the 10V needed for RS-232 output levels. The MAX201 a

MAX6887METE+ : Hex/Quad, Power-Supply Supervisory Circuits The MAX6887/MAX6888 multivoltage supply supervisors provide several voltage-detector inputs, one watchdog input, and three outputs. Each voltage-detector input offers a factory-set undervoltage and overvoltage threshold. Manual reset and margin disable in

MAX9259 : Gigabit Multimedia Serial Link With Spread Spectrum And Full-Duplex Control Channel The MAX9259/MAX9260 chipset presents Maxim\'s gigabit multimedia serial link (GMSL) technology. The MAX9259 serializer pairs with the MAX9260 deserializer to form a complete digital serial link for joint transmissio

DS1315S-33 : Phantom Time Chip The DS1315 Phantom Time Chip is a combination of a CMOS timekeeper and a nonvolatile memory controller. In the absence of power, an external battery maintains the timekeeping operation and provides power for a CMOS static RAM. The watch keeps track of hundredths of seconds, second

MAX16023PTAV12+T : Battery-Backup Circuits With Regulated Output Voltage The MAX16023/MAX16024 low-power battery-backup circuits with a regulated output are capable of delivering up to 100mA output current. The MAX16023/MAX16024 include a low-dropout regulator, a microprocessor (P) reset circuit, and a battery switc

MAX6440UTEHSD7+T : MAX6439, MAX6440, MAX6441, MAX6442 Low-Power, Single-/dual-level Battery Monitors With Hysteresis And Integrated µP Reset

DS26524GA5+ : Interface - Drivers, Receivers, Transceiver Integrated Circuit (ics) Line Interface Unit (LIU) Tray 3.135 V ~ 3.465 V; IC TXRX T1/E1/J1 QUAD 256-CSBGA Specifications: Number of Drivers/Receivers: 4/4 ; Type: Line Interface Unit (LIU) ; Voltage - Supply: 3.135 V ~ 3.465 V ; Package / Case: 256-LBGA, CSBGA ; Packaging: Tray ; Protocol: T1/E1/J1 ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

LM4040CIM7-2.0 : 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO3 Specifications: Package Type: SOT23, Other, ROHS COMPLIANT, SOT-23, 3 PIN ; VREF: 2.49 to 2.51 volts ; TC: 100 ppm/C ; Operating Temperature: -40 to 125 C (-40 to 257 F)

 
0-C     D-L     M-R     S-Z