Details, datasheet, quote on part number: MAX2623
PartMAX2623
CategoryCommunication => Freq/Signal Converters/Generators
DescriptionFully Monolithic 900mhz Sige Vco in 8-pin Umax
CompanyMaxim Integrated Products
DatasheetDownload MAX2623 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

o Fully Monolithic o Guaranteed Performance o On-Chip 50 Output Match o Wide Choice of Frequencies to +5.5V Single-Supply Operation o Low-Current Shutdown Mode o Smaller than Modules (8-Pin MAX Package)

The MAX2622/MAX2623/MAX2624 self-contained voltage-controlled oscillators (VCOs) combine an integrated oscillator and output buffer in a miniature 8-pin MAX package. The inductor and varactor elements of the tank circuits are integrated on-chip, greatly simplifying application of the part. In addition, the center frequency of oscillation and frequency span are factory preset to provide a guaranteed frequency range versus control voltage. An external tuning voltage controls the oscillation frequency. The output signals are buffered by an amplifier stage matched on-chip to 50. The MAX2622/MAX2623/MAX2624 operate from to +5.5V supply voltage and require only 8mA of supply current. In shutdown mode, the supply current is reduced to 0.1A.

Applications

to 868MHz European ISM Band (MAX2622) DECT 1/2 Frequency to 928MHz ISM Band, to 928MHz ISM Band, IF (MAX2624)

TEMP. RANGE to +85C PIN-PACKAGE 8 MAX 8 MAX 8 MAX

For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.

VCC to +6V TUNE, SHDN GND.................................-0.3V to (VCC + 0.3V) OUT GND...............................................-0.3V to (VCC + 0.6V) Continuous Power Dissipation (TA +70C) 8-Pin MAX (derate 5.7mW/C above = +70C).....457mW Operating Temperature to +85C Junction Temperature......................................................+150C Storage Temperature to +150C Lead Temperature (soldering, 10s).................................+300C

Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

(Typical Operating Circuit, VCC to +5.5V, VTUNE 1.4V, V SHDN = 2V, OUT = unconnected, to +85C, unless otherwise noted. Typical values are at VCC = +25C.) (Note 1) PARAMETER Supply Voltage Supply Current Shutdown Supply Current SHDN Input Voltage Low SHDN Input Voltage High SHDN Input Current Low SHDN Input Current High TUNE Input Current V SHDN 0.6V V SHDN 2.0V 0.4V VTUNE 2.4V V SHDN 0.6V CONDITIONS MIN 8 0.1 TYP MAX UNITS A nA

(Typical Operating Circuit, VCC to +5.5V, VTUNE 2.4V, V SHDN = +25C, unless otherwise noted. Typical values measured at VCC = +3V.) (Note 1) PARAMETER Oscillator Frequency Range CONDITIONS MAX2622, VTUNE +85C MAX2623, VTUNE +75C MAX2624, VTUNE to +85C Phase Noise Floor Maximum Tuning Gain (Note 2) Output Power Return Loss (Note 3) Harmonics Load Pulling Supply Pushing VSWR = 2:1, all phases VCC stepped from to 3.3V VTUNE to 2.4V VTUNE = 0.4V (Note 3) fOFFSET = 100kHz fOFFSET = 1MHz MIN TYP MAX 950 998 dBc/Hz dBm/Hz MHz/V dBm dB dBc MHzp-p kHz/V MHz UNITS

Note 1: Specifications are production tested = +25C. Limits over temperature are guaranteed by design and characterization. Note 2: Tuning gain is measured at VTUNE = 0.4V with a 0.2V step 0.6V. At low VTUNE, tuning gain is highest. Note 3: Measurements taken MAX262_ EV kit.

(VCC = +3.0V, VTUNE 2.4V, V SHDN = +25C, unless otherwise noted.)


 

Related products with the same datasheet
MAX2622EUA
MAX2623EUA
MAX2624
MAX2624EUA
Some Part number from the same manufacture Maxim Integrated Products
MAX2623EUA Fully Monolithic 900mhz Sige Vco in 8-pin Umax
MAX2623EVKIT Evaluation Kits
MAX2624 Fully Monolithic 900mhz Sige Vco in 8-pin Umax
MAX2624EVKIT Evaluation Kits
MAX262A P Programmable, Universal Switched Capacitor Filter
MAX262BENG Microprocessor Programmable Universal Active Filters
MAX262BM P Programmable, Universal Switched Capacitor Filter
MAX263 -
MAX2630 VHF-to-microwave, +3v, General-purpose Amplifiers
MAX2632EUK-T
MAX2633
MAX263AC -
MAX263ACPI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263AM -
MAX263AMJI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263BC -
MAX263BCPI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263BM -
MAX263BMJI VHF-to-microwave, +3v, General-purpose Amplifiers
MAX263C -
MAX2640 400mhz to 2500mhz Sige Ultra-low-noise Amplifiers

MAX155AEPI : High-Speed, 8-Channel, 8-Bit ADC With Simultaneous Track/holds And Reference

MAX6316LUK27DW-T : Watchdog 5-Pin P Supervisory Circuits With Watchdog And Manual Reset

MAX6327-29 : 3-Pin/5-Pin 3-Pin, Ultra-low-power SC70/SOT P Reset Circuits

MX584KH : Pin Programmable Precision Voltage Reference

MAX1030BCTI-T : 10-Bit 300ksps ADCs With FIFO, Temp Sensor, Internal Reference The MAX1026/MAX1028/MAX1030 are serial 10-bit analog-to-digital converters (ADCs) with an internal reference and an internal temperature sensor. These devices feature on-chip FIFO, scan mode, internal clock mode, internal averaging, and

MAX2041_1 : Evaluation Kit

MAX6715AUTSVD1+T : Dual/Triple, Ultra-Low-Voltage, SOT23 P Supervisory Circuits The MAX6715AMAX6729A/MAX6797A are ultra-low-voltage microprocessor (??P) supervisory circuits designed to monitor two or three system power-supply voltages. These devices assert a system reset if any monitored supply falls below its fac

MAX11332 : 3Msps, 12-/10-Bit, 8-/16-Channel ADCs With Post-Mux External Signal Conditioning Access The MAX11329–MAX11332 are 12-/10-bit with external reference and 500kHz, full-linear-bandwidth, high-speed, low-power, serial-output successive approximation register (SAR) analog-to-digital converters (ADCs).

MAX6801UR30D1-T : 3-Pin, Low-Power µP Reset Circuits The MAX6800/MAX6801/MAX6802 microprocessor (µP) supervisory circuits monitor the power supplies in 2.85V to 5.0V µP and digital systems. They increase circuit reliability and reduce cost by eliminating external components and adjustments. These devices perfo

MAX6383LT20D6 : SC70/DFN, Single/Dual Low-Voltage, Low-Power P Reset Circuits The MAX6381MAX6390 microprocessor (P) supervisory circuits monitor power-supply voltages from +1.8V to +5.0V while consuming only 3A of supply current at +1.8V. Whenever VCC falls below the factory-set reset thresholds, the reset ou

MAX333AEWP-T : QUAD 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO20 Specifications: Applications: Industrial ; Supply Voltage (VS): -15 to 20 volts ; Ron: 45 ohms ; tON: 175 ns ; tOFF: 145 ns ; VISO: 72 dB ; &nb916;RON: 2 ohms ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: TSSOP, 4.40 MM, TSSOP-20 ; Number of Pins: 20 ; Number of Devices: 4

MX7538JN-T : PARALLEL, WORD INPUT LOADING, 0.8 us SETTLING TIME, 14-BIT DAC, UUC24 Specifications: Package Type: DIE-24 ; Screening Level: Commercial ; Pins: 24 ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

 
0-C     D-L     M-R     S-Z