Details, datasheet, quote on part number: SMP6LC65
PartSMP6LC65
Category
TitleTVS/Zener Protection
DescriptionTvsarray Series
CompanyMicrosemi Corporation
DatasheetDownload SMP6LC65 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

This 16 pin 2 line Bidirectional LOW CAPACITANCE array is designed for use in applications where protection is required at the board level. Providing protection from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4, and effects of secondary lighting as stated by IEC 1000-4-5. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a peak power of 600 watts for an 10x1000 sec pulse and are designed to be used for secondary surge protection on telephone lines. This device can be used in either common or differential mode applications. For example in the circuit diagram on the following page use: TIP to (A) and (C) to ground, RING to (B) and (D) to ground for common mode, or TIP to (A) and RING to (C), or TIP to (B) and RING to (D) for differential mode.

FEATURES

600 watts Peak Pulse Power 10x1000 Protects up through 12 Volt Components Protects 4 Unidirectional lines or 2 Bidirectional Lines Provides electrically isolated protection SO-16 Packaging UL 94V-0 Flammability Classification

Molded SO-16 Surface Mount Weight: 0.128 grams (approximate) Body Marked with Logo, and device number Pin #1 defined by DOT on top of package

Tape & Reel EIA Standard 481-1-A 13 inch reel 2,500 pieces (OPTIONAL Carrier tubes 50 pcs per (STANDARD)

Operating Temperatures: C 0 Storage Temperature: +150 C Peak Pulse Power: 600 Watts (10/1000 sec, Figure 1 and 2) Pulse Repetition Rate: <.01%

ELECTRICAL CHARACTERISTICS PER LINE @ 25C Unless otherwise specified

STAND-OFF VOLTAGE VWM BREAKDOWN VOLTAGE VBR @10 mA VOLTS MIN 7.22 13.3 CLAMPING VOLTAGE VC @ IPP VOLTS MAX 12.4 19.9 MAXIMUM LEAKAGE CURRENT @VWM ID A TYP 300 2.0 PEAK PULSE CURRENT 10/1000 S IPP AMPS TYP 10 CAPACITANCE (f=1 MHz) @0V C PER LINE PAIR pF TYP 30

NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product selected voltage should be equal to or greater than the continuous or peak operating voltage of the circuit to be protected. Application: The SMP6LCXX product is designed for transient voltage suppression protection of components at the board level. is an ideal product to be used for protection of HIGH SPEED I/O TRANSCEIVERS.

FIGURE 1 Peak Pulse Power Vs Pulse Time

 

Related products with the same datasheet
SMP6LC50
Some Part number from the same manufacture Microsemi Corporation
SMS03 Transient Voltage Suppressor, Package : See_factory
SMS03C
SMS05
SMS05C
SMS12
SMS12C
SMS15
SMS15C
SMS24
SMS24C
SMZ100 Transient Voltage Suppressor, Package : SOT-23
SMZ5.6 Transient Voltage Suppressor
SMZ51 Zenerarray Series
SMZ8.2 Transient Voltage Suppressor
SMZ82 Transient Voltage Suppressor, Package : SOT-23
SP4460 Zener Voltage Regulator Diode
SP4460US
SP4461
SP4461US
SP4462
SP4462US
 
0-C     D-L     M-R     S-Z