|Description||Quad 2-input Multiplexer|
|Company||Motorola Semiconductor Products|
|Datasheet||Download MC10159FN datasheet
The is a quad two channel multiplexer with enable. It incorporates common enable and common data select inputs. The select input determines which data inputs are enabled. A high (H) level enables data inputs D10, D20, and D30. A low (L) level enables data inputs D11, D21, and D31. Any change on the data inputs will be reflected at the outputs while the enable is low. Input levels are inverted at the output. 218 mW typ/pkg (No Load) tpd 2.5 ns typ (Data 3.2 ns typ (Select to Q) tr, 2.5 ns typ (20%80%)
L SUFFIX CERAMIC PACKAGE CASE 62010 P SUFFIX PLASTIC PACKAGE CASE 64808 FN SUFFIX PLCC CASE 77502
Pin assignment is for DualinLine Package. For PLCC pin assignment, see the Pin Conversion Tables on page 611 of the Motorola MECL Data Book (DL122/D).Characteristic Power Supply Drain Current Input Current
Output Voltage Output Voltage Threshold Voltage Threshold Voltage Switching Times Propagation Delay Rise Time Fall TimeLogic 1 Logic 0 Logic 1 Logic 0 (50 Load) Data Input Select Input Enable Input to 80%)
TEST VOLTAGE APPLIED TO PINS LISTED BELOW VIHmax VILmin VIHAmin VILAmax VEE V
Output Voltage Output Voltage Threshold Voltage Threshold Voltage Switching Times Propagation Delay
Logic 1 Logic 0 Logic 1 Logic 0 (50 Load) Data Input Select Input Enable Input to 80%)
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50ohm resistor to 2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner.FN SUFFIX PLASTIC PLCC PACKAGE CASE 77502 ISSUE C
NOTES: 1. DATUMS L, M, AND N DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM T, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
|Some Part number from the same manufacture Motorola Semiconductor Products|
|MC10159L Quad 2-input Multiplexer|
|MC10160L 12-bit Parity Generator-checker|
|MC10161FN Binary to 1-8 Decoder (low)|
|MC10162FN Binary to 1-8 Decoder (high)|
|MC10164FN 8-line Multiplexer|
|MC10165L 8-input Priority Encoder|
|MC10168P Quad Latch|
|MC10170L 9+2-bit Parity Generator/checker|
MC14014BCP : 8-bit Static Shift Register
MC68HC05P4DW : M68HC05 Family MC68HC05P4A Technical Data
MC68HC908QT1VP : M68HC08 Family MC68HC908QY4, MC68HC908QT4, MC68HC908QY2, MC68HC908QT2, MC68HC908QY1, MC68HC908QT1 Data Sheet
MC74F132N : Quad 2-input NAND Schmitt Trigger Fast Shottky TTL
MC88916DW80 : Documentation
S3S12XEP100J1MVL : Microcontrollers
MPC8360TVVAGFHA : Powerquicc¢â II Pro Processor Revision 2.x TBGA Silicon Hardware Specifications
MMA1250EG : MMA1250KEG: Z-AXIS SENSITIVITY MICROMACHINED ACCELEROMETER Â±5g The MMA series of silicon capacitive, micromachined accelerometers feature signal conditioning, a 2-pole low pass filter and temperature compensation. Zero-g offset full scale span and filter cut-off are factory set and require
54AC04D : Hex Inverter. ICC reduced on 54AC only Outputs source/sink mA 'ACT04 has TTL-compatible inputs Standard Military Drawing (SMD) 596287609 n For Military 54ACT04 device see 54ACTQ04 FACT is a registered trademark of Fairchild Semiconductor Corporation. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors.
74AC11648NT : Registered Transceivers. ti 74AC11648, Octal Bus Transceivers And Registers.
74LV154 : CMOS/BiCMOS->LV/LVQ/LVX Family->Low Voltage. 4-line to 16-line Decoder/demultiplexer.
AD7591DI : di CMOS Analog Switches With Data Latches.
LF11331D : Quad SPST JFET Analog Switches. These devices are a monolithic combination of bipolar and JFET technology producing the industry's first one chip quad JFET switch. A unique circuit technique is employed to maintain a constant resistance over the analog voltage range ± 10V. The input is designed to operate from minimum TTL levels, and switch operation also ensures a break-before-make.
MC100EP56DT : Multiplexers. 3.3V / 5V Ecl Dual Differential 2:1 Multiplexer , Package: Tssop, Pins=20.
MC74AC32 : CMOS/BiCMOS->AC/ACT Family. Quad 2 Input OR GATE. Figure 1. Pinout: 14Lead Packages Conductors (Top View) Rating DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Sink/Source Current, per Pin DC VCC or GND Current per Output Pin Storage Temperature Symbol VCC Vin Vout Iin Iout ICC Tstg Value 0.5 to VCC 0.5.
MC74HCT541ADTR2 : Buffers. Octal 3-State Non Inverting Buffer/line Driver , Package: Tssop, Pins=20.
MM74C175 : Bipolar->TTL Family. Quad D Flip-flop. The MM54C175 MM74C175 consists of four positive-edge triggered D type flip-flops implemented with monolithic CMOS technology Both are true and complemented outputs from each flip-flop are externally available All four flipflops are controlled by a common clock and a common clear Information at the D inputs meeting the set-up time requirements is transferred.
NC7SV32 : Tinylogic Ulp-a 2-Input OR GATE (Preliminary). The is a single 2-Input OR Gate from Fairchild's Ultra Low Power-A (ULP-A) Series of TinyLogic. ULP-A is ideal for applications that require extreme high speed, high drive and low power. This product is designed for a wide low voltage operating range to 3.6V VCC) and applications that require more drive and speed than the TinyLogic ULP series, but still.
SN54AHCT373 : CMOS/BiCMOS->HC/HCT Family. Octal Transparent D-type Latches With 3-state Outputs.
SN74ABT16241ADGGR : Non-Inverting Buffers and Drivers. ti SN74ABT16241A, 16-Bit Buffers/drivers With 3-State Outputs.
SN74ALS1034D : Non-Inverting Buffers and Drivers. ti SN74ALS1034, Hex Noninverting Drivers.
SN74HC283 : Bipolar->F Family. 4-bit Binary Full Adders With Fast Carry.
SN74LS352D : Dual 4-input Multiplexer. The is a very high-speed Dual 4-input Multiplexer with Common Select inputs and individual Enable inputs for each section. It can select two bits of data from four sources. The two buffered outputs present data in the inverted (complementary) form. The 74LS352 is the functional equivalent of the SN54/ 74LS153 except with inverted outputs. Inverted Version.
SN74LS366A : Bipolar->LS Family. Hex Bus Driver With 3-state Outputs.
SN74LVTH2245DBLE : Standard Transceivers. ti SN74LVTH2245, 3.3-V Abt Octal Bus Transceivers With 3-State Outputs.
74HC58PW-T : HC/UH SERIES, DUAL 6-INPUT AND-OR GATE, PDSO14. s: Gate Type: AND, OR ; Supply Voltage: 5V ; Logic Family: CMOS ; Inputs: 6 ; Propagation Delay: 35 ns ; Operating Temperature: -40 to 125 C (-40 to 257 F) ; Pin Count: 14.
933812610623 : F/FAST SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDSO16. s: Output Characteristics: 3-State, TRUE ; Supply Voltage: 5V ; Package Type: 3.90 MM, PLASTIC, MS-012AC, SOT-109-1, SO-16 ; Logic Family: TTL ; Number of Pins: 16 ; Inputs: 2 ; Propagation Delay: 7 ns ; Operating Temperature: 0 to 70 C (32 to 158 F).