Details, datasheet, quote on part number: MC10216FNR2
PartMC10216FNR2
CategoryLogic => Receivers
DescriptionHigh Speed Triple Line Receiver , Package: Plcc, Pins=20
CompanyON Semiconductor
DatasheetDownload MC10216FNR2 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The is a high speed triple differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (VBB) is made available at pin 11 to make the device useful as a Schmitt trigger, or in other applications where a stable reference voltage is necessary. Active current sources provide the MC10216 with excellent common mode noise rejection. If any amplifier in a package is not used, one input of that amplifier must be connected to VBB (pin 11) to prevent upsetting the current source bias network. Complementary outputs are provided to allow driving twisted pair lines, to enable cascading of several amplifiers in a chain, or simply to provide complement outputs of the input logic function. 100 mW typ/pkg (No Load) tpd 1.8 ns typ (Single ended) 1.5 ns typ (Differential) tr, 1.5 ns typ (20%­80%)

CDIP­16 L SUFFIX CASE PDIP­16 P SUFFIX CASE AWLYYWW MC10216P AWLYYWW MC10216L AWLYYWW

*VBB to be used to supply bias to the MC10216 only and bypassed (when used) with 0.1 µF capacitor. When the input pin with bubble goes positive, it's respective output pin with bubble goes positive.

Device MC10216P MC10216FN Package PDIP­16 PLCC­20 Shipping 25 Units / Rail 25 Units / Rail 46 Units / Rail

Pin assignment is for Dual­in­Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 18 of the ON Semiconductor MECL Data Book (DL122/D).

Characteristic Power Supply Drain Current Input Current
Output Voltage Output Voltage Threshold Voltage Threshold Voltage Reference Voltage

* Delay is 1.5ns when inputs are driven differentially. Delay is 1.8ns when inputs are driven single ended.

Output Voltage Output Voltage Threshold Voltage Threshold Voltage Reference Voltage Switching Times Propagation Delay

Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50­ohm resistor to ­2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner.


 

Related products with the same datasheet
MC10216P
Some Part number from the same manufacture ON Semiconductor
MC10216L High Speed Triple Line Receiver, Package: Cdip, Pins=16
MC10216P High Speed Triple Line Receiver , Package: Plcc, Pins=20
MC10231 High Speed Dual Type D Master-slave Flip-flop
MC10231FN High Speed Dual Type D-type Master-slave Flip-flop , Package: Plcc, Pins=20
MC10231FNR2 High Speed Dual Type D-type Master-slave Flip-Flop, Package: Plcc, Pins=20
MC10231P High Speed Dual Type D-type Master-slave Flip-flop , Package: Plcc, Pins=20
MC1066 Acpi-compliant Smbus Temperature Sensor With Internal And External Diode Input
MC10E016 8-bit SYNCH Binary Counter
MC10E016FN 5V Ecl 8-Bit Synchronous Binary up Counter , Package: Plcc, Pins=28
MC10E016FNR2 5V Ecl 8-Bit Synchronous Binary up Counter, Package: Plcc, Pins=28
MC10E101 Quad 4-input Or/nOR GATE
MC10E101FN 5V Ecl Quad 4-Input Or/nOR GATE , Package: Plcc, Pins=28
MC10E104 Quint 2-input And/nand Gate
MC10E104FN Quint 2-Input And/nand Gate , Package: Plcc, Pins=28
MC10E107 Quint 2-input Xor/xnOR GATE
MC10E107FN 5V Ecl Quint 2-Input Xor/xnOR GATE , Package: Plcc, Pins=28
MC10E111 1:9 Differential Clock Driver
MC10E111FN 5V Ecl 1:9 Differential Clock Driver , Package: Plcc, Pins=28
MC10E111FNR2 5V Ecl 1:9 Differential Clock Driver, Package: Plcc, Pins=28
MC10E111SFN 5V Ecl 1:9 Differential Clock Driver , Package: Plcc, Pins=28
MC10E112 Quad Drive, Common Enable
 
0-C     D-L     M-R     S-Z