Details, datasheet, quote on part number: TS461CLT
PartTS461CLT
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers => Rail to Rail
DescriptionOutput Rail to Rail Op-amps
CompanyST Microelectronics, Inc.
DatasheetDownload TS461CLT datasheet
Cross ref.Similar parts: NCS7101SN2T1, OPA743NA, OPA743NA/250, OPA743NA/3K, OPA743NA/3KG4
Quote
Find where to buy
 
  

 

Features, Applications
s HIGH DYNAMIC FEATURES s LARGE OUTPUT SWING

DESCRIPTION The TS46x is operational amplifiers able to operate with voltages as low as 1.35V and to reach a minimum 2Vpp of output swing when supplied with 2.5V. This device is well suited for every kind of portable and battery-supplied equipment where low noise and low distortion are key. The TS461/2/4 are a cost-attractive access to the range of the Rail to Rail Op-Amps from STMicroelectronics. APPLICATION

s Sound cards s PDA s CD players s Recording equipments s Multimedia s Microphone preamplifier
Package Part Temperature Number Range +70C SOT23 Marking K105 TS464CN-TS464CD-TS464CPT

N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) only available in Tape & Reel (PT) L = Tiny Package (SOT23-5) only available in Tape & Reel (LT) S = MiniSO Package (MiniSO) only available in Tape & Reel (ST)

Symbol VCC Vid Vin Toper Tstd Tj Rthjc Supply voltage
Differential Input Voltage Input Voltage Range

Operating Free Air Temperature Range Storage Temperature Range Maximum Junction Temperature Thermal Resistance Junction to Case TSSOP8 TSSOP14 Human Body Model Lead Temperature (soldering, 10sec)

All voltages values, except differential voltage are with respect to network group terminal. Differential voltages are non-inverting input terminal with respect to the inverting input terminal. The magnitude of input and output voltages must never exceed VCC +0.3V. Short-circuits can cause excessive heating and destructive dissipation.

Symbol VCC Vicm Supply Voltage Common Mode Input Voltage Range Parameter Value to 10 VDD +1.15 to VCC - 1.15 Unit V

ELECTRICAL CHARACTERISTICS VCC = 2.5V, VDD = -2.5V, Tamb = 25C (unless otherwise specified)

Symbol Vio Input Offset Voltage Tmin. Tamb Tmax. Input Offset Voltage Drift Vicm = 0V Input Offset Current Vicm = 0V Tmin. Tamb Tmax. Input Bias Current Vicm = 0V Tmin. Tamb Tmax. Common Mode Input Voltage Range Common Mode Rejection Ratio Vicm = 1.35V Supply Voltage Rejection Ratio Vcc to 3V Large Signal Voltage Gain High Level Output Voltage Low Level Output Voltage Supply Current, per amplifier Unity gain - no load Gain Bandwith Product = 100kHz Slew Rate = 1, Vin = 1V Equivalent Input Noise Voltage = 100kHz Total Harmonic Distortion 2k dB V/s 4 nV ----------Hz -2 2.8 MHz V mA Parameter Min. Typ. 1 Max. 5 7 Unit mV V/C V dB


 

Related products with the same datasheet
TS461C
TS461CD
TS462
TS462C
TS462CD
TS462CN
TS462CPT
TS462CST
TS462ID
TS462IN
TS462IP
Some Part number from the same manufacture ST Microelectronics, Inc.
TS462 Output Rail to Rail Op-amps
TS462CDT
TS462CN
TS464CDT
TS464CN
TS482 100MW Stereo Headphone Amplifier
TS482IDT
TS482IQT
TS4851 1W LouDSPeaker & 2X160MW Headset BTL Drivers With Digital Volume Control
TS4851IJT Mono 1 W Speaker And Stereo 160 MW Headset BTL Drivers With Digital Volume Control
TS4855 LouDSPeaker & Headset Driver With Volume Control
TS4855IJT Mono 1 W Speaker And Stereo 160 MW Headset BTL Drivers With Digital Volume Control
TS486 Stereo Headphone Amplifier With Standby Active Low
TS486-1 100mw Stereo Headphone Amplifier With Standby Mode
TS486-1IST Stereo Headphone Amplifier With Standby Active Low
TS486-2 100mw Stereo Headphone Amplifier With Standby Mode
TS486ID Stereo Headphone Amplifier With Standby Active Low
TS487
TS487-1 100mw Stereo Headphone Amplifier With Standby Mode
TS4871 1W Mono Audio Amplifier With Standby Active High
TS4871ID Output Rail to Rail 1W Audio Power Amplifier With Standby Mode

M295V100-T120N6R : 1 Mbit 128kb x8 or 64kb X16, Boot Block Single Supply Flash Memory

PSD4135F1V-15JI : Flash In-system-programmable Peripherals For 16-bit MCUs

PSD835G1V-C-15UI : Configurable Memory System on a Chip For 8-bit Microcontrollers

UPSD3214B-24T1 : Flash Programmable System Device with 8032 Microcontroller Core

M95256-WDW6G/A : 256 Kbit Serial SPI bus Eeprom with high Speed Clock

UPSD3233BV-40T6 : Flash Programmable System Devices with 8032 Microcontroller Core and 64kbit SRAM

LM2904WHYDT : Low Power dual Operational Amplifier

NAND256R4M2AZB5F : 256/512mb/1gb (x8/x16, 1.8/3v, 528 Byte Page) NAND Flash Memories + 256/512mb (x16/x32, 1.8v) Lpsdram, MCP

M28W320ECB85ZB6F : 32mbit (2Mb x16) and 64mbit (4Mb x16) 3V Supply, Uniform Block, Secure Flash Memories

M24512-DFCS3TP/AB : EEPROM 5V Specifications: Memory Category: PROM, EEPROM

M621256-15E1 : 256K X 1 STANDARD SRAM, 12 ns, PDSO24 Specifications: Memory Category: SRAM Chip ; Density: 262 kbits ; Number of Words: 256 k ; Bits per Word: 1 bits ; Package Type: SOJ, 0.300 INCH, PLASTIC, SOJ-24 ; Pins: 24 ; Logic Family: CMOS ; Supply Voltage: 5V ; Access Time: 12 ns ; Operating Temperature: 0 to 70 C (32 to 158 F)

 
0-C     D-L     M-R     S-Z