Details, datasheet, quote on part number: TS462CN
PartTS462CN
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers => Rail to Rail
DescriptionOutput Rail to Rail Op-amps
CompanyST Microelectronics, Inc.
DatasheetDownload TS462CN datasheet
Cross ref.Similar parts: NJM2100D
Quote
Find where to buy
 
  

 

Features, Applications
s HIGH DYNAMIC FEATURES s LARGE OUTPUT SWING

DESCRIPTION The TS46x is operational amplifiers able to operate with voltages as low as 1.35V and to reach a minimum 2Vpp of output swing when supplied with 2.5V. This device is well suited for every kind of portable and battery-supplied equipment where low noise and low distortion are key. The TS461/2/4 are a cost-attractive access to the range of the Rail to Rail Op-Amps from STMicroelectronics. APPLICATION

s Sound cards s PDA s CD players s Recording equipments s Multimedia s Microphone preamplifier
Package Part Temperature Number Range +70C SOT23 Marking K105 TS464CN-TS464CD-TS464CPT

N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) only available in Tape & Reel (PT) L = Tiny Package (SOT23-5) only available in Tape & Reel (LT) S = MiniSO Package (MiniSO) only available in Tape & Reel (ST)

Symbol VCC Vid Vin Toper Tstd Tj Rthjc Supply voltage
Differential Input Voltage Input Voltage Range

Operating Free Air Temperature Range Storage Temperature Range Maximum Junction Temperature Thermal Resistance Junction to Case TSSOP8 TSSOP14 Human Body Model Lead Temperature (soldering, 10sec)

All voltages values, except differential voltage are with respect to network group terminal. Differential voltages are non-inverting input terminal with respect to the inverting input terminal. The magnitude of input and output voltages must never exceed VCC +0.3V. Short-circuits can cause excessive heating and destructive dissipation.

Symbol VCC Vicm Supply Voltage Common Mode Input Voltage Range Parameter Value to 10 VDD +1.15 to VCC - 1.15 Unit V

ELECTRICAL CHARACTERISTICS VCC = 2.5V, VDD = -2.5V, Tamb = 25C (unless otherwise specified)

Symbol Vio Input Offset Voltage Tmin. Tamb Tmax. Input Offset Voltage Drift Vicm = 0V Input Offset Current Vicm = 0V Tmin. Tamb Tmax. Input Bias Current Vicm = 0V Tmin. Tamb Tmax. Common Mode Input Voltage Range Common Mode Rejection Ratio Vicm = 1.35V Supply Voltage Rejection Ratio Vcc to 3V Large Signal Voltage Gain High Level Output Voltage Low Level Output Voltage Supply Current, per amplifier Unity gain - no load Gain Bandwith Product = 100kHz Slew Rate = 1, Vin = 1V Equivalent Input Noise Voltage = 100kHz Total Harmonic Distortion 2k dB V/s 4 nV ----------Hz -2 2.8 MHz V mA Parameter Min. Typ. 1 Max. 5 7 Unit mV V/C V dB


 

Related products with the same datasheet
TS461C
TS461CD
TS461CLT
TS462
TS462C
TS462CD
TS462CPT
TS462CST
TS462ID
TS462IN
TS462IP
Some Part number from the same manufacture ST Microelectronics, Inc.
TS462CPT Output Rail to Rail Op-amps
TS464CDT
TS464CN
TS482 100MW Stereo Headphone Amplifier
TS482IDT
TS482IQT
TS4851 1W LouDSPeaker & 2X160MW Headset BTL Drivers With Digital Volume Control
TS4851IJT Mono 1 W Speaker And Stereo 160 MW Headset BTL Drivers With Digital Volume Control
TS4855 LouDSPeaker & Headset Driver With Volume Control
TS4855IJT Mono 1 W Speaker And Stereo 160 MW Headset BTL Drivers With Digital Volume Control
TS486 Stereo Headphone Amplifier With Standby Active Low
TS486-1 100mw Stereo Headphone Amplifier With Standby Mode
TS486-1IST Stereo Headphone Amplifier With Standby Active Low
TS486-2 100mw Stereo Headphone Amplifier With Standby Mode
TS486ID Stereo Headphone Amplifier With Standby Active Low
TS487
TS487-1 100mw Stereo Headphone Amplifier With Standby Mode
TS4871 1W Mono Audio Amplifier With Standby Active High
TS4871ID Output Rail to Rail 1W Audio Power Amplifier With Standby Mode
TS4871IQT Output Rail to Rail 1w Audio Power Amplifier With Standby Mode
TS4871IST Output Rail to Rail 1W Audio Power Amplifier With Standby Mode
 
0-C     D-L     M-R     S-Z