Details, datasheet, quote on part number: TS3V330PWR
PartTS3V330PWR
CategorySemiconductors => Switches and Multiplexers => Protocol Specific Switches/Muxes
Part familyTS3V330 Quad SPDT Wide Bandwidth Video Switch with Low On-State Resistance
DescriptionQuad SPDT Wide Bandwidth Video Switch with Low On-State Resistance 16-TSSOP -40 to 85
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload TS3V330PWR datasheet
Quote
Find where to buy
 
PackagesSSOP (DBQ) | 16
Specifications 
Bandwidth(Max)(MHz)300
VIL(Max)(V)0.8
Turn off Time (Disable)(Max)(ns)3.5
Operating Temperature Range(C)-40 to 85
Package GroupSOIC,SSOP,TSSOP,TVSOP,VQFN
VCC(Min)(V)3
Off Isolation(Typ)(dB)-50
ProtocolsRGB,Composite
Approx. Price (US$)0.35 | 1ku
Input/Ouput Voltage(Min)(V)0
Input/Output Continuous Current(Max)(mA)128
Crosstalk(dB)-80
OFF-state leakage current(Max)(µA)1
Number of Channels(#)4
Ron(Max)(Ohms)10
Input/Output OFF-state Capacitance(Typ)(pF)10
Input/Ouput Voltage(Max)(V)3.6
Input/Output ON-state Capacitance(Typ)(pF)17
ICC(Typ)(uA)10
ESD Charged Device Model(kV)1
Ron(Typ)(Ohms)5
Bandwidth(MHz)300
Turn on Time (Enable)(Max)(ns)6.5
VIH(Min)(V)2
VCC(Max)(V)3.6
ICC(Max)(uA)10
ESD HBM(Typ)(kV)2
Additional FeaturesPowered off protection
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
16PWTSSOPR-PDSO-G2000LARGE T&RTF330 4.451.65
Application notes
• Preventing Excess Power Consumption on Analog Switches
Analog switches are extensively used for switching audio signals in battery-powered applications, such as mobile phones. In any cases, the switch is powered directly from the battery, but it receives control signals from a lower voltage processor GPIO. For | Doc

 

Features, Applications
TS3V330 QUAD SPDT WIDEBANDWIDTH VIDEO SWITCH WITH LOW ONSTATE RESISTANCE

(DG = 0.1 Degree Typ) Wide Bandwidth (BW = 300 MHz Min) Low Crosstalk (XTALK -80 dB Typ) Low Power Consumption (ICC 3 A Max) Bidirectional Data Flow, With Near-Zero Propagation Delay Low ON-State Resistance (ron = 3 Typ) Rail-to-Rail Switching on Data I/O Ports (0 to VCC) VCC Operating Range From 3.6 V Ioff Supports Partial-Power-Down Mode Operation Data and Control Inputs Provide Undershoot Clamp Diode Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Performance Tested Per JESD - 2000-V Human-Body Model (A114-B, Class II) - 1000-V Charged-Device Model (C101) Suitable for Both RGB and Composite-Video Switching

The TI TS3V330 video switch 4-bit 1-of-2 multiplexer/demultiplexer with a single switch-enable (EN) input. When EN is low, the switch is enabled and the D port is connected to the S port. When EN is high, the switch is disabled and the high-impedance state exists between the D and S ports. The select (IN) input controls the data path of the multiplexer/demultiplexer. ORDERING INFORMATION

TA QFN - RGY SOIC to 85C SSOP (QSOP) - DBQ TSSOP - PW TVSOP - DGV PACKAGE Tape and reel Tube Tape and reel Tape and reel Tube Tape and reel Tape and reel ORDERABLE PART NUMBER TS3V330 TF330 TOP-SIDE MARKING TF330

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Low differential gain and phase make this switch ideal for composite and RGB video applications. This device has wide bandwidth and low crosstalk, making it suitable for high-frequency applications as well. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. This switch maintains isolation during power off. To ensure the high-impedance state during power up or power down, EN should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

FUNCTION TABLE INPUTS H X INPUT/OUTPUT S2 Z PIN DESCRIPTIONS PIN NAME IN EN DESCRIPTION Analog video I/Os Analog video I/Os Select input Switch-enable input FUNCTION D port = S1 port D port = S2 port Disconnect

PARAMETER DEFINITIONS PARAMETER RON IOZ IOS VIN VEN CIN COFF CON VIH VIL VH VIK VI VO IIH IIL II IO Ioff tON tOFF BW XTALK OIRR DG DESCRIPTION Resistance between the D and S ports, with the switch in the ON state Output leakage current measured at the D and S ports, with the switch in the OFF state Short-circuit current measured at the I/O pins Voltage at the IN pin Voltage at the EN pin Capacitance at the control (EN, IN) inputs Capacitance at the analog I/O port when the switch is OFF Capacitance at the analog I/O port when the switch is ON Minimum input voltage for logic high for the control (EN, IN) inputs Minimum input voltage for logic low for the control (EN, IN) inputs Hysteresis voltage at the control (EN, IN) inputs I/O and control (EN, IN) inputs diode clamp voltage Voltage applied to the or S pins when S is the switch input Voltage applied to the or S pins when S is the switch output Input high leakage current of the control (EN, IN) inputs Input low leakage current of the control (EN, IN) inputs Current into the or S pins when S is the switch input Current into the or S pins when S is the switch output Output leakage current measured at the or S ports, with VCC = 0 Propagation delay measured between 50% of the digital input 90% of the analog output when switch is turned ON Propagation delay measured between 50% of the digital input 90% of the analog output when switch is turned OFF Frequency response of the switch in the ON state measured -3 dB Unwanted signal coupled from channel to channel. Measured in -dB. XTALK = 20 log VO/VI. This is a nonadjacent crosstalk. Off isolation is the resistance (measured in -dB) between the input and output with the switch OFF. Magnitude variation between analog input and output pins when the switch is ON and the dc offset of composite video signal varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is from 0.714 V. Phase variation between analog input and output pins when the switch is ON and the dc offset of composite-video signal varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is from 0.714 V. Static power-supply current Variation of ICC for a change in frequency in the control (EN, IN) inputs This is the increase in supply current for each control input that is at the specified voltage level, rather than VCC or GND.


 

Related products with the same datasheet
TS3V330D
TS3V330DBQR
TS3V330DGVR
TS3V330DGVR
TS3V330DR
TS3V330PW
TS3V330RGYR
TS3V330DBQRE4
TS3V330DBQRG4
TS3V330DGVRE4
TS3V330DGVRG4
Some Part number from the same manufacture Texas Instruments, Inc.
TS3V330RGYR Quad SPDT Wide Bandwidth Video Switch With Low On-state Resistance<<<>>>the ti TS3V330 Video Switch is a 4-bit 1-of-2 Multiplexer/demultiplexer With a Single Switch-enable (EN) Input. When en is Low, The Switch
TS5A23157 10-Ohm SPDT Analog Switch
TS5A23157 10-Ohm SPDT Analog Switch<<<>>>the TS5A23157 is a Dual, Single-pole, Double-throw (SPDT) Analog Switch Designed to Operate From 1.65 V to 5.5 V. This Device CAN Handle Both Digital And Analog Signals.
TS5A23157DGSR 10-Ohm SPDT Analog Switch
TS5A23157DGSR 10-Ohm SPDT Analog Switch<<<>>>the TS5A23157 is a Dual, Single-pole, Double-throw (SPDT) Analog Switch Designed to Operate From 1.65 V to 5.5 V. This Device CAN Handle Both Digital And Analog Signals.
TS5A23157DGST 10-Ohm SPDT Analog Switch
TS5A23157DGST 10-Ohm SPDT Analog Switch<<<>>>the TS5A23157 is a Dual, Single-pole, Double-throw (SPDT) Analog Switch Designed to Operate From 1.65 V to 5.5 V. This Device CAN Handle Both Digital And Analog Signals.
TS5L100 Quad SPDT Wide Bandwidth Lan Switch With Low On-state Resistance<<<>>>the ti TS5L100 Lan Switch is a 4-bit 1-of-2 Multiplexer/demultiplexer With a Single Switch-enable (E) Input. When e is Low, The Switch
TS5V330 Quad SPDT Wide Bandwidth Video Switch With Low On-state Resistance<<<>>>the ti TS5V330 Video Switch is a 4-bit 1-of-2 Multiplexer/demultiplexer With a Single Switch-enable (EN) Input. When en is Low, The Switch
TSB11C01 Ieee 1394-1995 Triple-cable Transceiver/arbiter
TSB11C01DL ti TSB11C01, Ieee 1394-1995, 5V, 3-Port, 100Mbps Physical Layer Controller
TSB11LV01 3v 1-port Ieee 1394-1995 Cable Transceiver/arbiter
TSB11LV01PT ti TSB11LV01, Ieee 1394-1995, 3.3V, 1-Port, 100Mbps Physical Layer Controller
TSB12C01A 1394 Serial Bus
TSB12C01AIPZ ti TSB12C01A, High Performance 5V Link Layer With 32-bit Host I/F, 2K Fifos
TSB12C01AWN High-speed Serial-bus Link-layer Controller
TSB12LV01A
TSB12LV01AIPZ ti TSB12LV01A, High Performance 3.3V Link Layer With 32-bit Host I/F, 2K Fifos
TSB12LV01B
TSB12LV01BIPZT ti TSB12LV01B, High Performance 1394 3.3V Link Layer For Telecom, Embedded & Industrial App.,32-Bit I/F, 2kb Fifo
TSB12LV01BIPZTEP ti TSB12LV01B-EP, Military Enhanced Plastic High Performance 1394 3.3V Link Layer For Telecom, Embedded & Indust. App.
 
0-C     D-L     M-R     S-Z