|Category||Optoelectronics => Display => LEDs => COINlight|
|Description||Coinlight With 8 Sideled, Red|
|Company||Osram Opto Semiconductors|
|Datasheet||Download OS-CM01B-A datasheet
Small height Wide viewing angle Easy installation Available in various colors
Border marker In-ground mounted luminaires Small signals Walkways
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data.
Ø Modules optimized for use with OSRAM Ø Diameter of the module: mm Ø Connection with screw terminals Ø Light emission in parallel to the mounting
Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.
Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module has to measured at the Tc-point according in a thermally constant status with a temperature sensor or a temperature sensitive label (available e.g. at RS-Components). For exact location of the Tc-point see drawing below.
Ø The LED module itself and all its components may not be mechanical stressed. Ø Assembly must not damage or destroy conducting paths on the circuit board.
The LED Module incorporates no protection against: Short circuits, Overload, Overheating. Therefore it is absolutely necessary to operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks. For dimming applications attention should be paid to specific references in "OPTOTRONIC Technical Guide".
OSRAM OPTOTRONIC power supplies are specifically designed with the necessary protection features for safe operation.
When using other power supplies other than OPTOTRONIC the following basic safety features are required, in addition to any other application specific concerns and local safety codes: Short circuit protection Overload protection Overheat protection Correct output voltage
Ø Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission. Ø Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and demage the LED module. Ø Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Ø Pay attention to ESD steps when mounting the module Ø The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. Ø Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. Ø For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features: - Optical transparency - UV-resistance - thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K - low permeability of steam for all climatic conditions - resistance against corrosive environment The lacquer APL of the company Electrolube http://www.electrolube.com met the conditions for the COINlight in our tests.
|Related products with the same datasheet|
|Some Part number from the same manufacture Osram Opto Semiconductors|
|OS-CM01B-B Coinlight With 8 Sideled, Red|
|OS-CM01C-B Coinlight, Blue|
|OS-CM01E-A1 Coinlight With 9 Topled, Red|
|OS-LM01A-A Linearlight, Red|
|OS-LM01M-RGB-B7 Linearlight Colormix|
|OS-LM03A-A Backlight, Red|
|OS-LM10A-A Linearlight Flex With 600 Topled, Red|
|OS-LM10M-RGB Linearlight Colormix Flex|
|OS-LM11A-A Linearlight Flex With 300 Sideled, Red|
|OS-ML01A-A Markerlight, Red|
|OS-ML90A-B Ledtag, Blue|
|OS-OP4x1-20 Linearlight Optics|
|OS-WL01A-A1 Effectlight With Lens, Red|
|OT06/100-240/10COS Electronical Stabilized Led-supply|
LY3336-S2U1-26 : 3 mm (T1) LED Hyper 3 MM (T1) Led, Orange, Non Diffused
LY5380-J : 5 mm (T1 ¾) LED 5 MM (T1 ¾) Led, Green, Diffused
SFH483L/ME7800 : Infrared Emitters in Metal Package Gaalas Infrared Emitter in TO-18 Metal Package, 880 NM
SFH4811 : Ir-lumineszenzdiode (950 nm) im To-46-gehäuse Infrared Emitter (950 nm) in To-46 Package Lead (Pb) Free Product - RoHS Compliant
LWQ18S-N1P2-24-1 : Lead (Pb) Free Product - RoHS Compliant
LA W5AM-JXKX-24-Z : High Power LEDs - Single Color Amber, 617nm 170 Degrees, 400mA » » » LEDs - High Power LEDs - High PowerHigh Power LEDs are defined as individual components that are greater than 0.15 watts (Voltage, nominal * Current, nominal). High Power LEDs have exploded in number over the last decade as new semiconductor technologies have allowed higher p
SFH-3400-2-3-Z : SMT Phototransistors Phototransistor in SMT Smart-dil Package
LT W51M-JYKZ-36-S-Z : LEDs - >75mA, High Brightness, Power Green; LED GOLDEN DRAGON TRUE GREEN SMD Specifications: Color: Green ; Package / Case: 2-SMD, Gull Wing ; Packaging: Tape & Reel (TR) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
LB A6SG-S1T2-35-Z : Hyper Sideled¢ç long life Enhanced Optical Power LED (thingan¢ç) Lead (Pb) Free Product - RoHS Compliant
SFH 325-3-Z : Optical - Photo Detectors - Phototransistors PHOTOTRANSISTOR NPN 980NM 2PLCC -; PHOTOTRANSISTOR NPN 980NM 2PLCC Specifications: Voltage - Collector Emitter Breakdown (Max): 35V ; Current - Collector (Ic) (Max): 15mA ; Current - Dark (Id) (Max): 50nA ; Power - Max: 165mW ; Orientation: Side View ; Mounting Type: Surface Mount, Right Angle ; Package / Case: 2-LCC (J-Lead) ; Wavelength: 980nm ; Viewing Angle: 12
LO T66F-AACA-24-1-Z : Standard LEDs - SMD Orange OSRAM TOPLED Black delivers a range of low power LEDs mounted in a black standard package. The black package offers significantly higher contrast with lower reflectivity than comparable white-package devices but with outstanding intensity. This makes the TOPLED Black ideal in display applications
GW MAEGB1.CM-QPQS-40S3-0-T02 : High Power LEDs - White White 4000K SOLERIQ P 6 OSRAM SOLERIQ Chip-On-Board family are ultra-high-power LEDs and feature simple installation with no surface mount technology (SMT) assembly required. A very small LES (light emitting surface) enables easy optics design, sharp shadows and a sparkling appearance. High luminous flux out of a single
AD8240 : Led Driver/monitorthe AD8240 is a Part That Addresses The Needs of The Automotive Lighting Industry. The Part Will Perform Two Major Functions: 1) Detect Led Lamp Failure BY Monitoring Current And 2) Supply a Constant Voltage to Drive Led Lamps..
SSI-LXH387YD-150 : T-4.9mm Freznel Lens Indicator, 6" Leads.
SSL-LX5063YD : T-5mm Short Lens Led.
TSL1301 : Linear Arrays. ti TSL1301, Linear Sensor Array. × 1 Sensor-Element Organization 300 Dots-Per-Inch (DPI) Sensor Pitch High Sensitivity Output Referenced to Ground Excellent High-Temperature Dark Signal Characteristics Operation to 2 MHz Single 5-V Supply The TSL1301 linear sensor array consists × 1 array of photodiodes, associated charge amplifier circuitry, and a pixel data-hold function that provides.
W7113MBDK : Material: Gan , Wavelength: 466nm. !LOW POWER CONSUMPTION. !POPULAR T-1 DIAMETER PACKAGE. !GENERAL PURPOSE LEADS. !RELIABLE AND RUGGED. ! LONG The Blue source color devices are made with GaN on SiC Light Emitting Diode. Static electricity and surge damage the LEDS. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery.
W934RK/2SRD : Material: Gaalas , Wavelength: 640nm. !PRE-TRIMMED LEADS FOR PC MOUNTING. !I.C. COMPATIBLE. ! BLACK The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode. !WIDE VIEWING ANGLE. !HIGH RELIABILITY LIFE MEASURED IN YEARS. ! UL Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead.
HFD3065-002-BBA : Fiber Optic Transmitters, Receivers, Transceivers Detector 850NM PIN Fiber Optic Receiver. s: Manufacturer: Honeywell ; Product Category: Fiber Optic Transmitters, Receivers, Transceivers ; RoHS: Details ; Product: Receiver ; Wavelength: 850 nm ; Maximum Output Current: 15 mA.
SSI-LXR4915GD-WR : LED Panel Mount Indicators Green 565nm Diffused 14.2mm Panel Mnt. s: Manufacturer: Lumex ; Product Category: LED Panel Mount Indicators ; RoHS: Details ; LED Size: 10 mm ; Illumination Color: Green ; Lens Color/Style: Green Diffused ; Wavelength: 565 nm ; Forward Current: 20 mA ; Forward Voltage: 2.2 V ; Luminous Intensity: 40 mcd ; Mounting Style:.
SSI-LXH600HD6V-150 : LED Panel Mount Indicators LED PMI. s: Manufacturer: Lumex ; Product Category: LED Panel Mount Indicators ; RoHS: Details ; LED Size: 5.5 mm ; Illumination Color: Red ; Lens Color/Style: Red Diffused ; Wavelength: 700 nm ; Packaging: Bulk ; Forward Voltage: 7 V ; Luminous Intensity: 4 mcd ; Mounting Style: Through Hole ; Factory Pack Quantity:.
1974 : Lamps - Incandescents, Neons White 6.0V; HALOGEN QUARTZ T-3 2P PARALL 6V. s: Color: White ; Lens Style/Size: Round, 9.5mm ; Lead Style: PC Pins (Through Hole) ; Voltage Rating: 6.0V ; MSCP (Mean Spherical Candle Power): 13 ; Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant.
SSF-LXH305AD-TR : LED , Round with Domed Top, 3mm 2V 20mA Amber Surface Mount, Right Angle; LED 3MM RA AMBER DIFFUSED SMD. s: Color: Amber ; Mounting Type: Surface Mount, Right Angle ; Configuration: Single ; Voltage Rating: 2V ; Current: 20mA ; Lens Style/Size: Round with Domed Top, 3mm ; Packaging: Tape & Reel (TR) ; Lens Type: Diffused, Tinted ; Lead Free Status:.
SSA-LXB10SIW-CUR : LED , Rectangle, 5mm x 1.5mm 2V 150mA Red (x 10) Through Hole; LED ARRAY 10-SEG CURVED RED. s: Color: Red (x 10) ; Mounting Type: Through Hole ; Configuration: 10 Segment ; Voltage Rating: 2V ; Current: 150mA ; Lens Style/Size: Rectangle, 5mm x 1.5mm ; Packaging: Bulk ; Lens Type: Diffused, White ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
551-0003-818F : LED , Round with Domed Top, 3mm 2.1V Green, 2V Red, 2.1V Yellow 10mA * Through Hole, Right Angle; LED CBI 3MM RED/GN/GN TRI LEVEL. s: Color: * ; Mounting Type: Through Hole, Right Angle ; Configuration: 3 Wide ; Voltage Rating: 2.1V Green, 2V Red, 2.1V Yellow ; Current: 10mA ; Lens Style/Size: Round with Domed Top, 3mm ; Packaging: Bulk ; Lens Type:.
109609001001808+ : Accessories; LED LIGHT / BACKLIGHT CONNECTOR. s: Accessory Type: Connector ; For Use With/Related Products: LED light / LED Backlight ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
GW5BQC15L02 : LEDs - High Brightness Power Modules White, Warm; LED MOD 3.6WATT ZENIGATA 2700K. s: Color: White, Warm ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
LEDS2-10-26 : LEDs - Spacers, Standoffs Black; LED SPACER FOR T-1 5/8 X 3/16". s: LED: T1 ; Length: 0.625" (15.9mm) ; Color: Black ; Material: PVC ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.