Details, datasheet, quote on part number: OS-CM01B-W
PartOS-CM01B-W
CategoryOptoelectronics => Display => LEDs => COINlight
TitleCOINlight
DescriptionCoinlight With 8 Sideled, Red
CompanyOsram Opto Semiconductors
DatasheetDownload OS-CM01B-W datasheet
  

 

Features, Applications

Small height Wide viewing angle Easy installation Available in various colors
Applications
Border marker In-ground mounted luminaires Small signals Walkways

Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data.

Modules optimized for use with OSRAM Diameter of the module: mm Connection with screw terminals Light emission in parallel to the mounting

Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.

Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module has to measured at the Tc-point according in a thermally constant status with a temperature sensor or a temperature sensitive label (available e.g. at RS-Components). For exact location of the Tc-point see drawing below.

The LED module itself and all its components may not be mechanical stressed. Assembly must not damage or destroy conducting paths on the circuit board.

The LED Module incorporates no protection against: Short circuits, Overload, Overheating. Therefore it is absolutely necessary to operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks. For dimming applications attention should be paid to specific references in "OPTOTRONIC Technical Guide".

OSRAM OPTOTRONIC power supplies are specifically designed with the necessary protection features for safe operation.

When using other power supplies other than OPTOTRONIC the following basic safety features are required, in addition to any other application specific concerns and local safety codes: Short circuit protection Overload protection Overheat protection Correct output voltage

Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission. Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and demage the LED module. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Pay attention to ESD steps when mounting the module The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. Damage by corrosion will not be honored as a materials defect claim. It is the users responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features: - Optical transparency - UV-resistance - thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K - low permeability of steam for all climatic conditions - resistance against corrosive environment The lacquer APL of the company Electrolube http://www.electrolube.com met the conditions for the COINlight in our tests.


 

Related products with the same datasheet
OS-CM01B-B
OS-CM01B-T
OS-CM01B-Y
Some Part number from the same manufacture Osram Opto Semiconductors
OS-CM01B-Y Coinlight With 8 Sideled, Red
OS-CM01C-B Coinlight, Blue
OS-CM01E-A1 Coinlight With 9 Topled, Red
OS-LM01A-A Linearlight, Red
OS-LM01M-RGB-B7 Linearlight Colormix
OS-LM03A-A Backlight, Red
OS-LM10A-A Linearlight Flex With 600 Topled, Red
OS-LM10M-RGB Linearlight Colormix Flex
OS-LM11A-A Linearlight Flex With 300 Sideled, Red
OS-ML01A-A Markerlight, Red
OS-ML01B-A
OS-ML01C-A
OS-ML02A-A
OS-ML03A-A
OS-ML90A-B Ledtag, Blue
OS-OP4x1-20 Linearlight Optics
OS-WL01A-A1 Effectlight With Lens, Red
OT06/100-240/10COS Electronical Stabilized Led-supply
OT06/100-240/24COS
OT12/230-240/10
OT20/230-240/24

OS-ML02A-TA : MARKERlight Markerlight, Red

SPLEY81 : Laser Diode Bars and Stacks in Metal Package Uncollimated Laser Stack, N X 40 W Cw, 808 NM

SFH 320-3/4-Z : Photodetector Transistors PHOTOTRANSISTOR Specifications: Manufacturer: Osram Opto Semiconductor ; Product Category: Photodetector Transistors ; RoHS:  Details ; Maximum Power Dissipation: 165 mW ; Maximum Dark Current: 50 nA ; Package / Case: PLCC-2 ; Collector- Emitter Voltage VCEO Max: 35 V ; Collector-Emitter Saturation Voltage: 15

LD W5AP-3V8A-35-Z : LEDs - >75mA, High Brightness, Power Blue; LED DIAMOND DRAGON 455NM DEEPBLU Specifications: Color: Blue ; Package / Case: 2-SMD, Gull Wing ; Packaging: Cut Tape (CT) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

LG P47K-H2K1-24-Z : LEDs -; LED POINTLED GRN 570NM REV SMD Specifications: Color: Green ; Lens Style/Size: Round with Flat Top, 2.1mm ; Millicandela Rating: 6.3mcd ; Voltage - Forward (Vf) Typ: 1.8V ; Wavelength - Dominant: 570nm ; Wavelength - Peak: 572nm ; Current - Test: 2mA ; Viewing Angle: 120 ; Lens Type: Clear ; Luminous Flux @ Current - Test: 19 ml

LS T67B-T1U1-1-Z : LEDs -; LED TOPLED RED 633NM 2-PLCC Specifications: Color: Red ; Lens Style/Size: Round with Flat Top, 2.4mm ; Millicandela Rating: 420mcd ; Voltage - Forward (Vf) Typ: 2.1V ; Wavelength - Dominant: 633nm ; Wavelength - Peak: 645nm ; Current - Test: 30mA ; Viewing Angle: 120 ; Lens Type: Clear ; Luminous Flux @ Current - Test: 1.2 lm

LW W5SG-GYHY-5K8L : LEDs - >75mA, High Brightness, Power White, Cool; LED WHITE DIFFUSED 1WATT SMD Specifications: Color: White, Cool ; Package / Case: 0.28" L x 0.24" W x 0.04" H (7mm x 6mm x 1mm) ; Packaging: Cut Tape (CT)

LY E65B-AABB-26-1-Z : LEDs -; LED YELLOW 587NM CLR 4-PLCC SMD Specifications: Color: Yellow ; Lens Style/Size: Round with Domed Top, 2.6mm ; Millicandela Rating: 1960mcd ; Voltage - Forward (Vf) Typ: 2.2V ; Wavelength - Dominant: 587nm ; Wavelength - Peak: 594nm ; Current - Test: 50mA ; Viewing Angle: 60 ; Lens Type: Clear ; Luminous Flux @ Current - Test: 2.

CO06A-W3-854 : SINGLE COLOR DISPLAY CLUSTER, WHITE, 50 mm Specifications: LED Color: WHITE ; Character Height: 50 mm (1.97 inch) ; Operating Temperature: -22 to 221 F (243 to 378 K)

LAP47F-V2BB-24-3A4B : SINGLE COLOR LED, AMBER, 1.6 mm Specifications: LED Type: AMBER ; Peak Wavelength: 624 nm (6240 Å) ; Viewing Angle: 120 degrees ; Luminous Intensity: 1.85 milliCandela ; Forward Current: 50 milliamps ; LED Package : ROHS COMPLIANT, SMT, 2 PIN

LBT676-J2L1-1 : SINGLE COLOR LED, BLUE, 2.4 mm Specifications: LED Type: Blue ; Peak Wavelength: 428 nm (4280 Å) ; Viewing Angle: 120 degrees ; Luminous Intensity: 0.0098 milliCandela ; Forward Current: 20 milliamps ; LED Package : PLASTIC, LCC-2

OS-LM01M-RGB-B8 : SINGLE COLOR DISPLAY CLUSTER, WHITE, 448 mm Specifications: LED Color: WHITE ; Character Height: 448 mm (17.64 inch)

 
0-C     D-L     M-R     S-Z