Details, datasheet, quote on part number: OS-LM11A-Y1
CategoryOptoelectronics => Display => LEDs => LINEARlight Flex
TitleLINEARlight Flex
DescriptionLinearlight Flex With 300 Sideled, Red
CompanyOsram Opto Semiconductors
DatasheetDownload OS-LM11A-Y1 datasheet
Find where to buy


Features, Applications

Linear separable LED strip on flexible printed circuit board with self-adhesive back Small height Available in various colors

Illuminated signs Channel letters Path & contour marking

Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data.

Modules optimized for use with OSRAM Entire Module consists of 300 LEDs Size of PCB ( LxWxH): x 5

regular intervals without damaging the rest of the module

Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.

Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module has to measured at the Tc-point according in a thermally constant status with a temperature sensor or a temperature sensitive label (available e.g. at RS-Components). For exact location of the Tc-point see drawing below.

The LED module itself and all its components may not be mechanical stressed. Assembly must not damage or destroy conducting paths on the circuit board.

The LED Module incorporates no protection against: Short circuits, Overload, Overheating. Therefore it is absolutely necessary to operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks. For dimming applications attention should be paid to specific references in "OPTOTRONIC Technical Guide".

OSRAM OPTOTRONIC power supplies are specifically designed with the necessary protection features for safe operation.

When using other power supplies other than OPTOTRONIC the following basic safety features are required, in addition to any other application specific concerns and local safety codes: Short circuit protection Overload protection Overheat protection Correct output voltage

Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission. Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and demage the LED module. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Please ensure that the power supply is of adequate power to operate the total load. At mounting on metallic surfaces there have be a electrical isolation at soldering points between module and the mounting surface. The maximum length of LINEARlight Flex 2072 mm for green, blue, white and yellow and 4200 mm for red with a two pole power feed at one end. The complete module 4200 mm can be operated with a two pole power feed in the middle of the module or from both ends. Pay attention to ESD steps when mounting the module The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. The ability to customize the length of the module by cutting at specifically marked points is a key feature of the product and hence the reason for no factory installed conformal coating. For these reasons, it is recommended that the user complete all module modifications first ( cutting, wiring) and then apply a conformal coating in the final stages of installation. Damage by corrosion will not be honored as a materials defect claim. It is the users responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circiut board garde conformal cating. The conformal coating should have the following features: - Optical transparency - UV-resistance - thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K - low permeability of steam for all climatic conditions - resistance against corrosive environment The lacquer APL of the company Electrolube met the conditions for the LINEARlight Flex in our tests.


Related products with the same datasheet
Some Part number from the same manufacture Osram Opto Semiconductors
OS-ML01A-A Markerlight, Red
OS-ML90A-B Ledtag, Blue
OS-OP4x1-20 Linearlight Optics
OS-WL01A-A1 Effectlight With Lens, Red
OT06/100-240/10COS Electronical Stabilized Led-supply
PD2435 Intelligent Display, 0.200 Inch, 4-Character, 5 X 7 Dot Matrix, Her
PDSP1880 Intelligent Display, 0.180 Inch, 8-Character, 5 X 7 Dot Matrix, Red
PDSP2110 Intelligent Display, 0.200 Inch, 8-Character, 5 X 7 Dot Matrix, Red
SCD55100A Intelligent Display, 0.145 Inch, 10-Character, 5 X 5 Dot Matrix, Red
SCD5580-A Intelligent Display, 0.145 Inch, 8-Character, 5 X 5 Dot Matrix, Red
SCDQ5541P Intelligent Display, 0.134 Inch, 4-Character, 5 X 5 Dot Matrix, Yellow
SCDV5540 Intelligent Display, 0.123 Inch, 4-Character, 5 X 5 Dot Matrix, Red
SCE5740 Intelligent Display, 0.180 Inch, 4-Character, 5 X 7 Dot Matrix, Red
SCE5780 Intelligent Display, 0.180 Inch, 8-Character, 5 X 7 Dot Matrix, Red

LB3356-K : 3 mm (T1) LED Blue LINE™ Hyper 3 MM (T1) Led, Blue, Diffused

LOK380-Q : ARGUS® LED T1 3 MM (T1) ARGUS® Led, Green, Non Diffused

LS3341-MQ : 3 mm (T1) LED 3 MM (T1) Led, Green, Non Diffused

LSY876-Q2S1-1 : Micro SIDELED® Micro SIDELED®, Amber, Colorless Clear

64602 : Product Information Bulletin Microscope LV Lamps Low Voltage Tungsten Halogen Lamps (microscope)

LOPT670-K+G : Multi Topled

LUW CQDP-KULQ-5E8G-1 : High Power LEDs - White Ultra White » » » LEDs for General Lighting ApplicationsThis covers an extremely broad group, including applications where LED lighting can be used in lieu of conventional lighting sources. Specifications: Manufacturer: Osram Opto Semiconductor ; Product Category: High Power LEDs - White ; R

LG V196-N1P2-24 : LEDs -; LED FIREFLY GREEN 570NM DIFF SMD Specifications: Color: Green ; Lens Style/Size: Rectangle with Flat Top, 1.35mm x 0.5mm ; Millicandela Rating: 49.5mcd ; Voltage - Forward (Vf) Typ: 2V ; Wavelength - Dominant: 570nm ; Wavelength - Peak: 572nm ; Current - Test: 20mA ; Viewing Angle: 140, 135 ; Lens Type: Diffused ; Luminous Flux @

LB A6SG-S2U1-35-Z : LEDs -; LED SIDELED 470NM BLUE SMD Specifications: Color: Blue ; Lens Style/Size: Round with Flat Top, 2.4mm ; Millicandela Rating: 392mcd ; Voltage - Forward (Vf) Typ: 3.2V ; Wavelength - Dominant: 470nm ; Wavelength - Peak: 465nm ; Current - Test: 20mA ; Viewing Angle: 120 ; Lens Type: Clear ; Luminous Flux @ Current - Test: 1.13

LS T676-P2S1-1-Z : TOPLED® Hyper TOPLED®, Amber, Colorless Clear

LWT6SC-S2U1-3K6L : SINGLE COLOR LED, WHITE, 2.4 mm Specifications: LED Type: White ; Viewing Angle: 120 degrees ; Luminous Intensity: 0.3920 milliCandela ; Forward Current: 20 milliamps ; LED Package : ROHS COMPLIANT, PLASTIC, SMT, LCC-2

0-C     D-L     M-R     S-Z