Details, datasheet, quote on part number: 1.5SMC36A
Part1.5SMC36A
CategoryDiscrete => TVS (Transient Transient Voltage Suppressors)
DescriptionPakage = SMC/DO-214AB ;; Devices Marking Code= DNJ ;; Nominal Voltage(V) =
CompanyTaiwan Semiconductor (TSC)
DatasheetDownload 1.5SMC36A datasheet
Cross ref.Similar parts: 1.5SMC24AT3, 1.5SMC36AT3, 1SMC30AT3, SM15T36A, SMCJ30, SMCJ30A, TPSMC36A
Quote
Find where to buy
 
  

 

Features, Applications
Voltage Range to 200 Volts 1500 Watts Peak Power
Features

For surface mounted application in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1 A above 10V High temperature soldering guaranteed: / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 1500 watts peak pulse power capability with 1000 us waveform by 0.01% duty cycle

Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Standard packaging: 16mm tape (EIA STD RS-481)

Rating at 25+ambient temperature unless otherwise specified. Type Number

Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) - Unidirectional Only Maximum Instantaneous Forward Voltage at 100.0A for Unidirectional Only (Note 4) Operating and Storage Temperature Range

Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. Mounted 8.0mm2 (.013mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. Devices for Bipolar Applications 1. For Bidrectional Use or CA Suffix for Types 1.5SMC6.8 through Types 1.5SMC200A. 2. Electrical Characteristics Apply in Both Directions.

GENERAL Device PART Marking NUMBER Code

Maximum Breakdown Voltage Test Stand-Off Current Voltage Reverse Leakage Peak Surge Clamping Temperature VBR @IT VWM at Vwm Current IPPM Voltage at IPPM Coefficient (Volts) (Note 1) O Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C)

Breakdown Voltage Stand-Off Maximum VBR Test Curren Voltage Reverse Leakage Peak Surge Clamping Temperature (Volts) (Note 1) @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C)

Notes: 1. VBR measured after IT applied for 300us, IT =square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. For bidirectional use or Ca suffix for types 1.5SMC 6.8 through 1.5SMC200A. 5. All terms and symbols are consistent with ANSI/IEEE C62.35.


 

Related products with the same datasheet
1.5SMC100
1.5SMC100A
1.5SMC100C
1.5SMC100CA
1.5SMC10A
1.5SMC10C
1.5SMC10CA
1.5SMC11
1.5SMC110
1.5SMC110A
1.5SMC110C
1.5SMC110CA
Some Part number from the same manufacture Taiwan Semiconductor (TSC)
1.5SMC36C Pakage = SMC/DO-214AB ;; Devices Marking Code= DNJ ;; Nominal Voltage(V) =
1M110Z Pakage = SMA/DO-214AC ;; Devices Marking Code= ;; Nominal Zener Voltage VZ @ Izt Voltage = 110
1N4001 Pakage = DO-41 ;; Max. Reverse Voltage VRM (V)= 50 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4001G
1N4001S Pakage = A-405 ;; Max. Reverse Voltage VRM (V)= 50 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4001SG
1N4002 Pakage = DO-41 ;; Max. Reverse Voltage VRM (V)= 100 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4002G
1N4002S Pakage = A-405 ;; Max. Reverse Voltage VRM (V)= 100 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4002SG
1N4003 Pakage = DO-41 ;; Max. Reverse Voltage VRM (V)= 200 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4003G
1N4003S Pakage = A-405 ;; Max. Reverse Voltage VRM (V)= 200 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4003SG
1N4004 Pakage = DO-41 ;; Max. Reverse Voltage VRM (V)= 400 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4004G
1N4004S Pakage = A-405 ;; Max. Reverse Voltage VRM (V)= 400 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4004SG
1N4005 Pakage = DO-41 ;; Max. Reverse Voltage VRM (V)= 600 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
1N4005G
1N4005S Pakage = A-405 ;; Max. Reverse Voltage VRM (V)= 600 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30
 
0-C     D-L     M-R     S-Z