Part  1.5SMC36CA 
Category  Discrete => TVS (Transient Transient Voltage Suppressors) 
Description  Pakage = SMC/DO214AB ;; Devices Marking Code= DNJ ;; Nominal Voltage(V) = 
Company  Taiwan Semiconductor (TSC) 
Datasheet  Download 1.5SMC36CA datasheet

Cross ref.  Similar parts: SM15T36CA, SMCJ30C, SMCJ30CA 
Quote 
Features, Applications 
Voltage Range to 200 Volts 1500 Watts Peak Power Features For surface mounted application in order to optimize board space Low profile package Builtin strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1 A above 10V High temperature soldering guaranteed: / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V0 1500 watts peak pulse power capability with 1000 us waveform by 0.01% duty cycle Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Standard packaging: 16mm tape (EIA STD RS481) Rating at 25+ambient temperature unless otherwise specified. Type NumberPeak Forward Surge Current, 8.3 ms Single Half Sinewave Superimposed on Rated Load (JEDEC method) (Note 3)  Unidirectional Only Maximum Instantaneous Forward Voltage at 100.0A for Unidirectional Only (Note 4) Operating and Storage Temperature Range Notes: 1. Nonrepetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. Mounted 8.0mm2 (.013mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sinewave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. Devices for Bipolar Applications 1. For Bidrectional Use or CA Suffix for Types 1.5SMC6.8 through Types 1.5SMC200A. 2. Electrical Characteristics Apply in Both Directions. GENERAL Device PART Marking NUMBER CodeMaximum Breakdown Voltage Test StandOff Current Voltage Reverse Leakage Peak Surge Clamping Temperature VBR @IT VWM at Vwm Current IPPM Voltage at IPPM Coefficient (Volts) (Note 1) O Min Max (mA) (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) Breakdown Voltage StandOff Maximum VBR Test Curren Voltage Reverse Leakage Peak Surge Clamping Temperature (Volts) (Note 1) @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) Notes: 1. VBR measured after IT applied for 300us, IT =square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. For bidirectional use or Ca suffix for types 1.5SMC 6.8 through 1.5SMC200A. 5. All terms and symbols are consistent with ANSI/IEEE C62.35. 
Related products with the same datasheet 
1.5SMC100 
1.5SMC100A 
1.5SMC100C 
1.5SMC100CA 
1.5SMC10A 
1.5SMC10C 
1.5SMC10CA 
1.5SMC11 
1.5SMC110 
1.5SMC110A 
1.5SMC110C 
1.5SMC110CA 
Some Part number from the same manufacture Taiwan Semiconductor (TSC) 
1.5SMC39 Pakage = SMC/DO214AB ;; Devices Marking Code= DNJ ;; Nominal Voltage(V) = 
1M110Z Pakage = SMA/DO214AC ;; Devices Marking Code= ;; Nominal Zener Voltage VZ @ Izt Voltage = 110 
1N4001 Pakage = DO41 ;; Max. Reverse Voltage VRM (V)= 50 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4001G 
1N4001S Pakage = A405 ;; Max. Reverse Voltage VRM (V)= 50 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4001SG 
1N4002 Pakage = DO41 ;; Max. Reverse Voltage VRM (V)= 100 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4002G 
1N4002S Pakage = A405 ;; Max. Reverse Voltage VRM (V)= 100 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4002SG 
1N4003 Pakage = DO41 ;; Max. Reverse Voltage VRM (V)= 200 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4003G 
1N4003S Pakage = A405 ;; Max. Reverse Voltage VRM (V)= 200 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4003SG 
1N4004 Pakage = DO41 ;; Max. Reverse Voltage VRM (V)= 400 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4004G 
1N4004S Pakage = A405 ;; Max. Reverse Voltage VRM (V)= 400 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4004SG 
1N4005 Pakage = DO41 ;; Max. Reverse Voltage VRM (V)= 600 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 
1N4005G 
1N4005S Pakage = A405 ;; Max. Reverse Voltage VRM (V)= 600 ;; Max. Aver. Rect. Current io (A)= 1 ;; Ifsm (A)= 30 