Details, datasheet, quote on part number: P4KE120CA
PartP4KE120CA
CategoryDiscrete => TVS (Transient Transient Voltage Suppressors)
DescriptionPakage = DO-41 ;; Devices Marking Code= ;; Nominal Voltage(V) = 10
CompanyTaiwan Semiconductor (TSC)
DatasheetDownload P4KE120CA datasheet
Cross ref.Similar parts: P6KE120CA, BZW04-102B, SA120CA
Quote
Find where to buy
 
  

 

Features, Applications
Voltage Range to 440 Volts 400 Watts Peak Power
Features

UL Recognized File # E-96005 Plastic package has Underwriters Laboratory Flammability Classification 94V-0 400W surge capability x 100us waveform, duty cycle: 0.01% Excellent clamping capability Low zener impedance Fast response time: Typically less than 1.0ps from 0 volts to VBR for unidirectional and 5.0 ns for bidirectional Typical IR less than 1 uA above 10V High temperature soldering guaranteed: / 10 seconds /.375",(9.5mm) lead length / 5lbs.,(2.3kg) tension

a Case: Molded plastic Lead: Axial leads, solderable per MIL-STD202, Method 208 Polarity: Color band denotes cathode except bipolar Weight: 0.012 ounce,0.3 gram Dimensions in inches and (millimeters)

Rating at 25C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%

Steady State Power Dissipation at TL=75C Lead Lengths.375", 9.5mm (Note 2) Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) Maximum Instantaneous Forward Voltage at 25.0A for Unidirectional Only (Note 4) Operating and Storage Temperature Range

Notes: 4. VF=3.5V for Devices of VBR 200V and VF=6.5V Max. for Devices VBR>200V. Devices for Bipolar Applications Notes: 1. For Bidirectional Use or CA Suffix for Types P4KE6.8 thru Types P4KE440. Notes: 2. Electrical Characteristics Apply in Both Directions.

Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. Notes: 2. Mounted on Copper Pad Area x 40 mm) Per Fig. 4. Notes: 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minutes Notes: 3. Maximum.

PEAK PULSE POWER (Ppp) or CURRENT (IPPM) DERATING IN PERCENTAGE, %
PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS 50% of lPPM
PM(AV), STEADY STATE POWER DISSIPATION, WATTS
HALF VALUE- lPPM 2 10/1000 sec. WAVEFORM as DEFINED by R.E.A.
lFSM, PEAK FORWARD SURGE CURRENT, AMPERES
FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY
Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method

Maximum Peak Pulse Current IPPM (Note 2)(Amps)

Notes: 1. VBR measured after IT applied for 300us, IT=square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. All terms and symbols are consistent with ANSI/IEEE C62.35.


 

Related products with the same datasheet
P4KE100
P4KE100A
P4KE100C
P4KE100CA
P4KE10A
P4KE10C
P4KE10CA
P4KE11
P4KE110
P4KE110A
P4KE110C
P4KE110CA
Some Part number from the same manufacture Taiwan Semiconductor (TSC)
P4KE12A Pakage = DO-41 ;; Devices Marking Code= ;; Nominal Voltage(V) = 10
 
0-C     D-L     M-R     S-Z