Development Boards - Evaluation Boards

W681511DK: Kit Development For W681511
The is a general-purpose single channel PCM CODEC with pin-selectable µ-Law or A-Law companding. The device is compliant with the ITU G.712 specification. It operates off of a single +5V power supply and is available
NCP3011GEVB: Board Eval Ncp3011 Buck Ctlr
The is a PWM device designed to operate from a wide input range and is capable of producing an output voltage as low 0.8 V. The NCP3011 provides 1.0 A gate driver and an internally set 400 kHz oscillator.
MAX15462C12EVKIT#: Eval Board For Max15462
The MAX15462C 12V evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the performance of the 42V, 300mA ultra-small, high-efficiency, synchronous step-down converter.
NCP170AXV120GEVB: Eval Board Ncp170axv120g
1.Check the position of jumper and correct this if necesary in acordance with the picture above. 2. Connect the test setup as shown Figure above 3. Appy an input voltage Vin V 4. Appy Iout = 0mA load.
410-069: Board Pmodhb3 2a H-bridge Module
Revised January 20, 2016 This manual applies to the PmodHB3 rev. E The Digilent PmodHB3 offers a 2A H-Bridge circuit with external feedback to drive small to medium sized DC motors. 2A H-bridge circuit
EV-MCS-LVBRD-Z: Eval Board
Power Management, Motor Control
TPS40041EVM-001: Evaluation Module For Tps40041
DC/DC, Step Down ; 1, Non-Isolated ; 1.8V ; 6A ; 3 V ~ 5.5 V ; Regulator
DC1084A-A: Board Demo Ltm4602
Demonstration circuit DC1084A-A features the LTM®4602, the high efficiency, high density step-down Module® regulator. The input voltage range is from to 20V. The output voltage is jumper programmable
STEVAL-ISA044V1: Board Eval Based On St1s10
Features 3 A synchronous 900 kHz step-down DC-DC converter with inhibit function based on the ST1S10 ) PWM mode operation with a fixed frequency or t(ssynchronized to an external frequency uc Inhibit pin available
BQ76925EVM: Eval Module For Bq76925
Power Management, Battery Monitor ; Yes, MCU, 16-Bit ; BQ76925, MSP430F2122 ; 3 ~ 6 Cells,
ATA6831-DK: Kit Development For Ata6831
Power Management, High and Low Side Driver (Internal FET) ; ATA6831
MAX8722AEVKIT: Kit Evaluation For Max8722a
Lighting, CCFL Backlight Controller ; MAX8722A
STM32F052B-DISCO: Board Disco Stm32f052b
STM32F0 ; Evaluation Platform ; MCU 32-Bit ; ARM® Cortex®-M0 ; Discovery Kit ; For Use With/Related
MIKROE-1820: Dev Board Flame Click
Flame clickTM is a fire detection solution. It carries a PT334-6B NPN silicon phototransistor that's covered in black epoxy and therefore sensitive only to infrared light. A potentiometer lets you calibrate
14-103-04-1-AIS-XILINX: Kit Nanoboard And Spartan3 Dc
NanoBoard ; FPGA ; Spartan?-3 ; Dev Board, Daughter Card and 12 Mo. Altium Designer Core Feature
MCP6V01RD-TCPL: Ref Design Thermcpl For Mcp6v01
Note the following details of the code protection feature on Microchip devices:· Microchip products meet the specification contained in their particular Microchip Data Sheet. · Microchip believes that
P0035: Card Ad/da Data Conversion
ii Development Board Version 1.0.0 Data Conversion HSMC Reference Manual Board Overview. 2­1 Configuration, Status and Setup Elements. 2­3 A/D Converter Clock Select Jumper J7). 2­4 Power Down Select Jumper
THS4508EVM: Evaluation Module For Ths4508
WIDEBAND, LOW NOISE, LOW DISTORTION FULLY DIFFERENTIAL AMPLIFIER FEATURES · Fully Differential Architecture· Common-Mode Input Range Includes the · Minimum Gain of 2 V/V (6 dB)· Bandwidth: 2 GHz· Slew
AD9233-125EBZ: Board Evaluation For Ad9233
FEATURES 1.8 V analog supply operation 3.3 V output supply SNR = 69.5 dBc (70.5 dBFS) to 70 MHz input SFDR = 85 dBc to 70 MHz input Low power: @ 125 MSPS Differential input with 650 MHz bandwidth On-chip

AD9233-80EBZ: Board Eval For Ad9233
PGA400Q1EVM: Eval Module For Pga400-q1
Interface, Sensor Signal Conditioner ; PGA400-Q1
M68EVB908GP32: Board Evaluation For Hc908gp32
HC08 ; Evaluation Platform ; MCU 8-Bit ; HC08 ; MC68HC908GP32 ; Mounting
TPS54550EVM-158: Evaluation Module For Tps54550
SWIFT? ; DC/DC, Step Down ; 1, Non-Isolated ; 3.3V ; 5A ;
SI5018-EVB: Board Evaluation For Si5018
EVALUATION BOARD FOR Si5018 SiPHYTM OC-48/STM-16 CLOCK AND DATA RECOVERY IC WITH FEC Features The Si5018 evaluation board provides a platform for testing and characterizing Silicon Laboratories OC-48,
MC-78F0712-KIT: Kit Ref System 78k0 Upd78f0712
On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company
EVB90621: Board Evaluation For Mlx90621
The a 16X4 array of pixels sensitive to thermal infrared radiation. It has improved considerably on speed and temperature resolution (x4) compared to the previous generation product. This exciting high
SMP-TPS61202-MVK: Kit Ref Mod/versatile Tps61202
MAVRK ; DC/DC, Step Up or Down ; 1, Non-Isolated ; 5V ; 0.3 V ~ 5 V ; Regulator
LMZ20502EVM: Eval Module For Lmz20502
SIMPLE SWITCHER® ; DC/DC, Step Down ; 1, Non-Isolated ; 1.8V ; 2A ; Voltage
LP5951MF-1.8EV: Board Evaluation Lp5951mf-1.8
1 - Single ; 1.8V ; 150mA ; 1.8 V ~ 5.5 V ; Positive Fixed ; Operating
TVP9900EVM: Tvp9900evm
Video, Video Processing ; TVP9900
THEVA215-2LANE: Eval Board Kit Thcv215-2lane
V-by-One® ; Interface, LVDS, Transmitter ; THCV215
BD9A300MUV-EVK-001: Eval Board Bd9a300muv
is a synchronous buck switching regulator with built-in low on-resistance power MOSFETs. It is capable of providing current to 3A.The SLLMTM control provides excellent efficiency characteristics in light-load
TPS2530EVM-636: Eval Module For Tps2530-636
Power Management, Power Distribution Switch (Load Switch) ; No ; TPS2530
TPS65270QEVM: Eval Module For Tps65270q
DC/DC, Step Down ; 2, Non-Isolated ; 1.2V, 1.8V ; 3A, 2A ; 4.5 V ~ 16 V ; Regulator
MAX4273EVKIT: Eval Kit For Max4273
The MAX4273 evaluation kit (EV kit) is a fully assembled and tested surface-mount hot-swap controller circuit board that provides current-limiting and DualSpeed/BiLevelTM fault protection. The circuit
ADP123-EVALZ: Board Evaluation Adjustable V
FEATURES Input voltage range: 5.5 V Output current range: 300 mA Output voltage accuracy: ±1% Operating temperature range: to +125°C This user guide explains the functionality of the ADP122/ ADP123 linear
TPS2560DRCEVM-424: Eval Module For Tps2560drc-424
Power Management, Power Distribution Switch (Load Switch) ; TPS2560
AFE5805EVM: Eval Module For Afe5805
Interface, Analog Front End (AFE) ; No ; AFE5805 ; 8 Channel LVDS Outputs
TW9907-TA1-GR-EVAL: Eval Board For Tw9907-ta1-gr
Techwell? ; Video, Video Decoder ; TW9907
MAX15090BEVKIT#: Eval Kit For Max15090
Power Management, Hot Swap Controller ; MAX15090B
DS21348DK: Kit Evaluation For Ds21348
Telecom, Line Interface Units (LIUs) ; DS21348
XIO2213BEVM: Eval Modul For Xio2213b
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include
STEVAL-MKI159V1: Eval Adapter Board Lsm9ds1 Dil24
Features The is an adapter board designed to facilitate the evaluation of MEMS inertial devices in the LSM9DS1 product family. The board offers an effective solution for fast system prototyping and device
ISL8240MEVAL4Z: Eval Board Dcdc Sdown Module
ISL8240MEVAL4Z Dual 20A/Optional 40A Cascadable Evaluation Board Setup Procedure The is a complete, dual step-down switching mode DC/DC module. The dual outputs can easily be paralleled for single-output,
FHS 40-P KIT 6-1P: Fhs 40 Pcb W/jumper Kit 10/10a
FHS ; Current Sensor ; ±10A ; Analog ; 206.2 mV/A ; 4.75 V ~ 5.25 V ;
MIC94305YMT-EV: Eval Board High Side Load Switch
Ripple Blocker? ; Power Management, Power Distribution Switch (Load Switch) ; MIC94305 ;
BQ24232EVM: Evaluation Module For Bq24232
bqTINY? III ; Power Management, Battery Charger ; No ; BQ24232 ; 1 Cell- Li-Ion/
T201-DEV1: Kit Dev Multitouch Control Wheel
Multi-Touch Control Wheel Software Development Kit User's Guide v1.0 Introduction. 3 What's in this Guide?. 3 What's in the Kit?. 3 Multi-Touch Control Wheel Features. 3 Multi-Touch Control Wheel Medical
ADM1270CP-EVALZ: Eval Board For Adm1270
Evaluating the ADM1270 High Voltage Input Protection Device FEATURES Controls supply voltages from 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs Inrush current

ADS1258EVM: Eval Modulde For Ads1258
1 ; 24 ; 125k ; SPI ; 0 ~ 5 V ;
AT89RFD-02: Kit Ref Design At83c22ok/23ok
PRE-CERTIFIED SMART CARD READER SOLUTIONS FOR USB LINK AT83C22OK and AT83C23OK are based on Atmel C51 MCUs and include OMNIKEY® firmware. These single-chip turnkey solutions can be quickly and easily integrated
LM89-1EVAL: Board Evaluation Lm89-1
Temperature ; 0°C ~ 125°C ; SMBus (2-Wire/I˛C) ; ±1°C ; 3 V ~ 3.6 V ; No ; Supplied
TPS2330EVM-184: Eval Mod For Tps2330-184
Power Management, Hot Swap Controller ; TPS2330
LM4675SDBD: Board Evaluation Lm4675sd
Ultra-Low EMI, Filterless, 2.65W, Mono, Class D Audio Power Amplifier with Spread Spectrum FEATURES ·2 Spread Spectrum Architecture Reduces EMI· Mono Class D Operation· No Output Filter Required for Inductive

LM4675SDBD/NOPB: Board Eval For Lm4675sd
LM4675TLBD: Board Evaluation Lm4675tl
LFE2M50E-S-EVN: Board Eval Latticeecp2m50 Serdes
ECP2M ; FPGA ; LFE2M50E ; Board, Cable, Power Supply
BOB-12918: Mcp4725 Dac Breakout
When learning about the world of microcontrollers, you will come across analog-to-digital converters quite frequently. These allows us to read in signals from analog sensors and convert them into a digital
TPS65310AEVM: Eval Board For Tps65310
Power Management, Integrated Power Supply ; TPS65310A-Q1
DK-LM3S815: Kit Dev For Lm3s815
Stellaris® ; Evaluation Platform ; MCU 32-Bit ; ARM® Cortex®-M3 ; RTOS ; For Use With/Related
HI5741-EVS: Evaluation Platform Hi5741
The 14-bit 100MHz Digital to Analog Converter. This current out DAC is designed for low glitch and high Spurious Free Dynamic Range operation. As a result, this DAC is ideally suited for Signal Reconstruction
KITFXLC95000EVM: Board Eval Fxlc95000
2 Notes 3 Block Diagram FXLC95000CL / MCU Circuit 5 Power and Battery Charger Circuit This document contains information proprietary to Freescale Semiconductor and shall not be used for engineering design,
NUMICRO-SDK: Kit Evauation Nuc100/120/130/140
NuMicro? ; Evaluation Platform ; MCU 32-Bit ; ARM® Cortex®-M0 ; NUC100, NUC120,
NCP1075PREGEVK: Ncp1075preg Eval Kit
The ac-supply pre-regulator demo board is a universal input, off-line, 15-W output, constant voltage power supply for powering E-meters or white goods applications. This pre-regulator is a specific function
BQ27505EVM: Eval Module For Bq27505
Impedance Track? ; Power Management, Battery Gauge ; No ; BQ27505 ; 1 Cell- Li-Ion
EVAL-ADE5169EBZ-2: Board Evaluation For Ad5169
Evaluation Kit for the Single-Phase Energy Metering IC with 8052 MCU, RTC, and LCD Driver (ADE71xx/ADE75xx/ADE51xx/ADE55xx Family) FEATURES Full evaluation kit including evaluation board hardware, evaluation
AN44140A-EVB-0: Board Eval For An44140a-vb
Sine-wave PWM drive system and rotor position detection method by 1-Hall-sensor FEATURES APPLICATIONS Various protection functions: under voltage lock out (UVLO), over voltage lock out (OVLO), thermal
TMDSDCDCLEDKIT: Kit Led Dvr C2000 Piccolo
C2000?, Piccolo? ; Reference Design, Embedded LED Lighting ; Yes, MCU, 32-Bit ; TMS320F28035 ; Primary
AD9558/PCBZ: Board Eval For Ad9558
Quad Input Multiservice Line Card Adaptive Clock Translator with Frame Sync AD9558 FEATURES Supports GR-1244 Stratum 3 stability in holdover mode Supports smooth reference switchover with virtually no
EVAL-ADM1023EB: Board Eval For Adm1023
ACPI-Compliant, High Accuracy Microprocessor System Temperature Monitor FEATURES Next generation upgrade of ADM1021 On-chip and remote temperature sensing Offset registers for system calibration 1°C accuracy
EVAL-AD5520EBZ: Board Eval For Ad5520
FEATURES Force/measure functions FIMV, FVMI, FVMV, FIMI, FNMV Force/measure voltage range V 4 user programmable force/measure current ranges ±4 mA (external resistors) 2 user programmable extended current
DP83848T-MAU-EK: Board Evaluation Dp83848t
Interface, Ethernet ; DP83848T
MAX77826EVKIT#: Eval Kit For Max77826
Power Management, Special Purpose Mobiles ; MAX77826
P9035A-EVK: Kit Evaluation Idtp9035a
Power Management, Wireless Power Supply ; IDTP9035A ; Transmitter
CRD-001: Board Eval Isol Sic Gate Driver
This article describes an implementation of an isolated gate driver suitable for testing and evaluating SiC MOSFETs in a variety of applications. This design replaces previous versions of this application
ADM00615: Board Remote Temp Sensor Mcp9902
Note the following details of the code protection feature on Microchip devices:· Microchip products meet the specification contained in their particular Microchip Data Sheet. · Microchip believes that
BMA222E-SHUTL: Shuttle Board Dev Kit Bma222e
Accelerometer, 3 Axis ; ±2g, 4g, 8g, 16g ; I˛C, Serial, SPI ; 64LSB/g, 32LSB/g, 16LSB/g, 8LSB/g ; Voltage
EVAL-CN0350-PMDZ: Eval Board Piezo Vibration
Precision, Low Noise, Quad CMOS, Rail to Rail Input/Output Op Amp 12-Bit, 1 MSPS, Single-Supply, Two-Chip Data Acquisition System for Piezoelectric Sensors Circuit Evaluation Boards CN0350 Circuit Evaluation
DB-SO8-LPC908: Board For Lpc908 8-soic
The USB-Dongle and Derivative Boards allow quick and easy ICP or ISP programming of many popular NXP Semiconductors microcontroller families such as the ARM7 LPC2xxx and 89V52X2. The unit also provides
TPA2001D1EVM: Eval Mod For Tpa2001d1
Class D ; 1-Channel (Mono) ; 1W x 1 @ 8 Ohm ; 2.7 V ~ 5.5 V ; Board
MAX9736AEVKIT+: Kit Eval For Max9736a
The MAX9736A evaluation kit (EV kit) is a fully assembled and tested printed-circuit board (PCB) that configures the MAX9736A Class D amplifier to drive x 15W into a pair of 8 speakers in stereo mode,
MAX125EVB16: Eval Kit For Max125
The MAX125/MAX126 evaluation systems (EV systems) consist a MAX125/MAX126 evaluation kit (EV kit) and a Maxim 68HC16MOD-16WIDE microcontroller (µC) module. The MAX125/MAX126 are high-speed, 8-channel,

MAX126EVB16: Eval Kit For Max126
LM5035AEVAL: Board Eval For Lm5035a
DC/DC, Step Down ; 1, Isolated ; 3.3V ; 30A ; 36 V ~ 75 V ; Regulator